Raspberry Pi Bootcode Read File: config.txt, 182 Read File: start.elf, 2883108 (bytes) Read File: fixup.dat, 6745 (bytes) MESS:00:00:01.021731:0: brfs: File read: /mfs/sd/config.txt MESS:00:00:01.025931:0: brfs: File read: 182 bytes MESS:00:00:01.108323:0: brfs: File read: /mfs/sd/config.txt MESS:00:00:01.112497:0: gpioman: gpioman_get_pin_num: pin LEDS_PWR_OK not defined MESS:00:00:01.129511:0: gpioman: gpioman_get_pin_num: pin WL_LPO_CLK not defined MESS:00:00:01.135219:0: gpioman: gpioman_get_pin_num: pin BT_ON not defined MESS:00:00:01.141897:0: gpioman: gpioman_get_pin_num: pin WL_ON not defined MESS:00:00:01.320783:0: gpioman: gpioman_get_pin_num: pin LEDS_PWR_OK not defined MESS:00:00:01.326600:0: *** Restart logging MESS:00:00:01.330485:0: brfs: File read: 182 bytes MESS:00:00:01.365192:0: hdmi: HDMI:hdmi_get_state is deprecated, use hdmi_get_display_state instead MESS:00:00:01.379077:0: brfs: File read: /mfs/sd/bcm2835-rpi-b.dtb MESS:00:00:01.383561:0: Loading 'bcm2835-rpi-b.dtb' to 0x100 size 0x4988 MESS:00:00:01.465401:0: brfs: File read: 18824 bytes MESS:00:00:01.471743:0: brfs: File read: /mfs/sd/config.txt MESS:00:00:01.480394:0: brfs: File read: 182 bytes MESS:00:00:01.486555:0: brfs: File read: /mfs/sd/cmdline.txt MESS:00:00:01.490516:0: Read command line from file 'cmdline.txt': MESS:00:00:01.496410:0: 'root=sd0a -s -v' MESS:00:00:03.392276:0: gpioman: gpioman_get_pin_num: pin EMMC_ENABLE not defined MESS:00:00:03.416092:0: brfs: File read: 152 bytes MESS:00:00:03.917337:0: brfs: File read: /mfs/sd/kernel.img MESS:00:00:03.921216:0: Loading 'kernel.img' to 0x8000 size 0x81ab50 MESS:00:00:03.927300:0: Device tree loaded to 0x1bfeb700 (size 0x483a) MESS:00:00:03.934409:0: uart: Set PL011 baud rate to 103448.300000 Hz MESS:00:00:03.941251:0: uart: Baud rate change done... MESS:00:00:03.944679:0: uart: Baud rate change done... MESS:00:00:03.950055:0: gpioman: gpioman_get_pin_num: pin SDCARD_CONTROL_POWER not defined pc : 0x00008060 off : 0x80000000 sp : 0x00974000 fdt : 0x1bfeb700 midr : 0x410fb767 revidr: 0x410fb767 mpidr : 0x410fb767 ttb0 : 0x00000000 ttb1 : 0x00000000 ttcr : 0x00000000 v6 : B sctlr:0x000500f8/0x000500f8 C uboot : 0x006506ac fdt : 0x1bfeb700 0x00974000 va:0x00000000 pa:0x00000000 nsec:0x0000000a attr:0x00001412 0x00974000[0x00000000]=0x00001412 0x00974000[0x00000001]=0x00101412 0x00974000[0x00000002]=0x00201412 0x00974000[0x00000003]=0x00301412 0x00974000[0x00000004]=0x00401412 0x00974000[0x00000005]=0x00501412 0x00974000[0x00000006]=0x00601412 0x00974000[0x00000007]=0x00701412 0x00974000[0x00000008]=0x00801412 0x00974000[0x00000009]=0x00901412 0x00974000 va:0x80000000 pa:0x00000000 nsec:0x0000000b attr:0x00001412 0x00974000[0x00000800]=0x00001412 0x00974000[0x00000801]=0x00101412 0x00974000[0x00000802]=0x00201412 0x00974000[0x00000803]=0x00301412 0x00974000[0x00000804]=0x00401412 0x00974000[0x00000805]=0x00501412 0x00974000[0x00000806]=0x00601412 0x00974000[0x00000807]=0x00701412 0x00974000[0x00000808]=0x00801412 0x00974000[0x00000809]=0x00901412 0x00974000[0x0000080a]=0x00a01412 DTB 0x00974000 va:0x1bf00000 pa:0x1bf00000 nsec:0x00000001 attr:0x00001412 0x00974000[0x000001bf]=0x1bf01412 CONSADDR 0x00974000 va:0x20200000 pa:0x20200000 nsec:0x00000001 attr:0x00000412 0x00974000[0x00000202]=0x20200412 ME0H0IK sctlr:0x000500f8/0x004501f9 virtual go [ 1.0000000] FDT<0x1bfeb700> [ 1.0000000] cpufunc [ 1.0000000] devmap [ 1.0000000] devmap: 20000000 -> 20ffffff @ f2000000 [ 1.0000000] SSSSSSSSSSSSSSSS [ 1.0000000] bootstrap [ 1.0000000] bcm283x_bootparams: memory size 469762048 [ 1.0000000] bcm283x_bootparams: arm clock 700000000 [ 1.0000000] bcm283x_bootparams: vpu clock 250000000 [ 1.0000000] bcm283x_bootparams: emmc clock 200000000 [ 1.0000000] bcm283x_bootparams: emmc2 clock 200000000 [ 1.0000000] bcm283x_bootparams: firmware rev 5df107ce [ 1.0000000] bcm283x_bootparams: board model 0 [ 1.0000000] bcm283x_bootparams: mac-address 6b55c6eb27b8 [ 1.0000000] bcm283x_bootparams: board rev d [ 1.0000000] bcm283x_bootparams: board serial 3ec6556b [ 1.0000000] bcm283x_bootparams: DMA channel mask 0x00007f35 [ 1.0000000] bcm283x_bootparams: cmdline bcm2708_fb.fbwidth=1824 bcm2708_fb.fbheight=984 bcm2708_fb.fbswap=1 dma.dmachans=0x7f35 bcm2708.boardrev=0xd bcm2708.serial=0x3ec6556b bcm2708.uart_clock=48000000 smsc95xx.macaddr=B8:27:EB:C6:55:6B vc_mem.mem_base=0x1ec00000 vc_mem.mem_size=0x20000000 root=sd0a -s -v [ 1.0000000] stdout [ 1.0000000] fb_format [ 1.0000000] consinit ok [ 1.0000000] uboot: args 0, 0xc42, 0x1bfeb700, 0x22f1e89c [ 1.0000000] NetBSD/evbarm (fdt) booting ... [ 1.0000000] FDT /memory [0] @ 0x0 size 0x1c000000 [ 1.0000000] initarm: memory start 0 end 1c000000 (len 1c000000) [ 1.0000000] initarm: fdt_build_bootconfig [ 1.0000000] Usable memory: [ 1.0000000] 1000 - 1bffffff [ 1.0000000] cpu_kernel_vm_init: kernel phys start 0 end 1c000000 [ 1.0000000] arm32_bootmem_init: kern_vtopdiff=0x80000000 [ 1.0000000] arm32_bootmem_init: kstartva=0x80008000, kernelstart=0x8000 [ 1.0000000] arm32_bootmem_init: memstart=0, memsize=0x1c000000 [ 1.0000000] arm32_bootmem_init: kernelstart=0x8000, kernelend=0x978000 [ 1.0000000] arm32_bootmem_init: kernel phys start 0x8000 end 0x978000 [ 1.0000000] arm32_bootmem_init: adding 112264 free pages: [0x978000..0x1bffffff] (VA 0x80978000) [ 1.0000000] arm32_bootmem_init: adding 8 free pages: [0..0x7fff] (VA 0x80000000) [ 1.0000000] arm32_kernel_vm_init: 3 L2 pages are needed to map 0x99e000 kernel bytes [ 1.0000000] arm32_kernel_vm_init: allocating page tables for kernel l1ptadd_pages: adding pv 0x80973eec (pa 0x978000, va 0x80978000, 4 pages) at tail [ 1.0000000] add_pages: appending pv 0x80822c10 (0x97c000..0x97cfff) to 0x978000..0x97bfff [ 1.0000000] add_pages: appending pv 0x80822c24 (0x97d000..0x97dfff) to 0x978000..0x97cfff [ 1.0000000] add_pages: appending pv 0x80822c38 (0x97e000..0x97efff) to 0x978000..0x97dfff [ 1.0000000] vmadd_pages: appending pv 0x80822c4c (0x97f000..0x97ffff) to 0x978000..0x97efff [ 1.0000000] add_pages: appending pv 0x80822c60 (0x980000..0x980fff) to 0x978000..0x97ffff [ 1.0000000] add_pages: appending pv 0x80822c74 (0x981000..0x981fff) to 0x978000..0x980fff [ 1.0000000] add_pages: appending pv 0x80822c88 (0x982000..0x982fff) to 0x978000..0x981fff [ 1.0000000] add_pages: appending pv 0x80822c9c (0x983000..0x983fff) to 0x978000..0x982fff [ 1.0000000] add_pages: appending pv 0x80822cb0 (0x984000..0x984fff) to 0x978000..0x983fff [ 1.0000000] add_pages: appending pv 0x80822cc4 (0x985000..0x985fff) to 0x978000..0x984fff [ 1.0000000] add_pages: appending pv 0x80822cd8 (0x986000..0x986fff) to 0x978000..0x985fff [ 1.0000000] arm32_kernel_vm_init: allocating stacks [ 1.0000000] add_pages: appending pv 0x808c68fc (0x987000..0x987fff) to 0x978000..0x986fff [ 1.0000000] add_pages: appending pv 0x808c68e8 (0x988000..0x988fff) to 0x978000..0x987fff [ 1.0000000] add_pages: appending pv 0x808c68d4 (0x989000..0x989fff) to 0x978000..0x988fff [ 1.0000000] add_pages: appending pv 0x808c68c0 (0x98a000..0x98afff) to 0x978000..0x989fff [ 1.0000000] add_pages: appending pv 0x808c68a8 (0x98b000..0x98cfff) to 0x978000..0x98afff [ 1.0000000] add_pages: appending pv 0x808c6910 (0x98d000..0x98efff) to 0x978000..0x98cfff [ 1.0000000] add_pages: appending pv 0x80973b54 (0x98f000..0x992fff) to 0x978000..0x98efff [ 1.0000000] Creating L1 page table at 0x80978000/0x00978000 [ 1.0000000] arm32_kernel_vm_init: kernel_base 80000000 KERNEL_L2PT_KERNEL_NUM 3 [ 1.0000000] arm32_kernel_vm_init: adding L2 pt (VA 0x8097c000, PA 0x97c000) for VA 0x80000000 (kernel) [ 1.0000000] arm32_kernel_vm_init: adding L2 pt (VA 0x8097d000, PA 0x97d000) for VA 0x80400000 (kernel) [ 1.0000000] arm32_kernel_vm_init: adding L2 pt (VA 0x8097e000, PA 0x97e000) for VA 0x80800000 (kernel) [ 1.0000000] arm32_kernel_vm_init: kernel_vm_base c0000000 KERNEL_L2PT_VMDATA_NUM 8 [ 1.0000000] arm32_kernel_vm_init: adding L2 pt (VA 0x8097f000, PA 0x97f000) for VA 0xc0000000 (vm) [ 1.0000000] arm32_kernel_vm_init: adding L2 pt (VA 0x80980000, PA 0x980000) for VA 0xc0400000 (vm) [ 1.0000000] arm32_kernel_vm_init: adding L2 pt (VA 0x80981000, PA 0x981000) for VA 0xc0800000 (vm) [ 1.0000000] arm32_kernel_vm_init: adding L2 pt (VA 0x80982000, PA 0x982000) for VA 0xc0c00000 (vm) [ 1.0000000] arm32_kernel_vm_init: adding L2 pt (VA 0x80983000, PA 0x983000) for VA 0xc1000000 (vm) [ 1.0000000] arm32_kernel_vm_init: adding L2 pt (VA 0x80984000, PA 0x984000) for VA 0xc1400000 (vm) [ 1.0000000] arm32_kernel_vm_init: adding L2 pt (VA 0x80985000, PA 0x985000) for VA 0xc1800000 (vm) [ 1.0000000] arm32_kernel_vm_init: adding L2 pt (VA 0x80986000, PA 0x986000) for VA 0xc1c00000 (vm) [ 1.0000000] Mapping kernel [ 1.0000000] arm32_kernel_vm_init: adding chunk for kernel text 0x8000..0x598fff (VA 0x80008000) [ 1.0000000] add_pages: adding pv 0x80973ed8 (pa 0x8000, va 0x80008000, 1425 pages) before pa 0x978000 [ 1.0000000] arm32_kernel_vm_init: adding chunk for kernel data/bss 0x599000..0x977fff (VA 0x80599000) [ 1.0000000] add_pages: adding pv 0x80973ec4 (pa 0x599000, va 0x80599000, 991 pages) before pa 0x978000 [ 1.0000000] Listing Chunks [ 1.0000000] arm32_kernel_vm_init: pv 0x80973ed8: chunk VA 0x80008000..0x80598fff (PA 0x8000, prot 5, cache 1) [ 1.0000000] arm32_kernel_vm_init: pv 0x80973ec4: chunk VA 0x80599000..0x80977fff (PA 0x599000, prot 3, cache 1) [ 1.0000000] arm32_kernel_vm_init: pv 0x80973eec: chunk VA 0x80978000..0x80992fff (PA 0x978000, prot 3, cache 1) [ 1.0000000] Mapping Chunks [ 1.0000000] arm32_kernel_vm_init: mapping chunk VA 0x80000000..0x80007fff (PA 0, prot 3, cache 1) [ 1.0000000] PPPPPPPP [ 1.0000000] arm32_kernel_vm_init: mapping chunk VA 0x80008000..0x80598fff (PA 0x8000, prot 5, cache 1) [ 1.0000000] PPPPPPPPLLLLLLLLLLLLLLLSSSSLLLLLLLLLPPPPPPPPP [ 1.0000000] arm32_kernel_vm_init: mapping last chunk VA 0x80599000..0x9bffffff (PA 0x599000, prot 3, cache 1) [ 1.0000000] PPPPPPPLLLLLLSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSS [ 1.0000000] devmap: 20000000 -> 20ffffff @ f2000000 [ 1.0000000] SSSSSSSSSSSSSSSS [ 1.0000000] Physical Virtual Num [ 1.0000000] Starting Ending Starting Ending Pages [ 1.0000000] text section: 0x00008000 0x00598fff 0x80008000 0x80598fff 1425 [ 1.0000000] data section: 0x00650000 0x00822b50 0x80650000 0x80822b50 467 [ 1.0000000] bss section: 0x00822b50 0x00969e00 0x80822b50 0x80969e00 328 [ 1.0000000] L1 page directory: 0x00978000 0x0097bfff 0x80978000 0x8097bfff 4 [ 1.0000000] ABT stack (CPU 0): 0x00987000 0x00987fff 0x80987000 0x80987fff 1 [ 1.0000000] FIQ stack (CPU 0): 0x00988000 0x00988fff 0x80988000 0x80988fff 1 [ 1.0000000] IRQ stack (CPU 0): 0x00989000 0x00989fff 0x80989000 0x80989fff 1 [ 1.0000000] UND stack (CPU 0): 0x0098a000 0x0098afff 0x8098a000 0x8098afff 1 [ 1.0000000] IDLE stack (CPU 0): 0x0098b000 0x0098cfff 0x8098b000 0x8098cfff 2 [ 1.0000000] SVC stack: 0x0098d000 0x0098efff 0x8098d000 0x8098efff 2 [ 1.0000000] Message Buffer: 0x0098f000 0x00992fff 0x8098f000 0x80992fff 4 [ 1.0000000] Free Memory: 0x00993000 0x1bffffff 112237 [ 1.0000000] Free Memory: 0x00000000 0x00007fff 8 [ 1.0000000] TTBR0=0x974000 TTBR1=0 TTBCR=0 CONTEXTIDR=0 [ 1.0000000] switching to new L1 page table @0x978000... [ 1.0000000] ttb (TTBR0=0x978000) OK [ 1.0000000] bootargs: bcm2708_fb.fbwidth=1824 bcm2708_fb.fbheight=984 bcm2708_fb.fbswap=1 dma.dmachans=0x7f35 bcm2708.boardrev=0xd bcm2708.serial=0x3ec6556b bcm2708.uart_clock=48000000 smsc95xx.macaddr=B8:27:EB:C6:55:6B vc_mem.mem_base=0x1ec00000 vc_mem.mem_size=0x20000000 root=sd0a -s -v [ 1.0000000] Memory regions: [ 1.0000000] 1000 - 7fff [ 1.0000000] 993000 - 1bffffff [ 1.0000000] nfreeblocks = 2, free_pages = 112245 (0x1b675) [ 1.0000000] bootstrap done. [ 1.0000000] vectors vbar=0x800262c0 0x800262c0 [ 1.0000000] init subsystems: stacks vectors undefined page pmap_physload [ 1.0000000] block 0 start 00993000 end 1c000000 [ 1.0000000] bp 0 start 00001000 end 00008000 [ 1.0000000] bp 1 start 00993000 end 1c000000 [ 1.0000000] start 00993000 end 1c000000... loading in freelist 0 [ 1.0000000] block 1 start 00000000 end 00008000 [ 1.0000000] bp 0 start 00001000 end 00008000 [ 1.0000000] start 00001000 end 00008000... loading in freelist 0 [ 1.0000000] bp 1 start 00993000 end 1c000000 [ 1.0000000] pmap kpm locks l1pt cache(l1pt) specials pools [ Kernel symbol table missing! ] [ 1.0000000] done. [ 1.0000000] mpstart [ 1.0000000] start 0096c000 end 00978000... loading in freelist 0 [ 1.0000000] uvmfault_init: advice 0 nback 3 nforw 4 [ 1.0000000] uvmfault_init: advice 1 nback 0 nforw 0 [ 1.0000000] uvmfault_init: advice 2 nback 8 nforw 7 [ 1.0000000] Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, [ 1.0000000] 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017, [ 1.0000000] 2018, 2019, 2020 The NetBSD Foundation, Inc. All rights reserved. [ 1.0000000] Copyright (c) 1982, 1986, 1989, 1991, 1993 [ 1.0000000] The Regents of the University of California. All rights reserved. [ 1.0000000] NetBSD 9.99.74 (RPI0EB) #47: Fri Oct 30 19:54:04 JST 2020 [ 1.0000000] rin@latipes:/sys/arch/evbarm/compile/RPI0EB [ 1.0000000] total memory = 448 MB [ 1.0000000] avail memory = 429 MB [ 1.0000000] entropy: no seed from bootloader [ 1.0000000] timecounter: Timecounters tick every 10.000 msec [ 1.0000000] Kernelized RAIDframe activated [ 1.0000000] armfdt0 (root) [ 1.0000000] simplebus0 at armfdt0: Raspberry Pi Model B Rev 2 [ 1.0000000] simplebus1 at simplebus0 [ 1.0000000] simplebus2 at simplebus0 [ 1.0000000] simplebus3 at simplebus0 [ 1.0000000] cpus0 at simplebus0 [ 1.0000000] cpu0 at cpus0: 700 MHz ARM1176JZ-S r0p7 (ARM11J V6ZK core) [ 1.0000000] cpu0: DC enabled IC enabled WB enabled LABT [ 1.0000000] cpu0: 16KB/32B 4-way L1 VIPT Instruction cache [ 1.0000000] cpu0: 16KB/32B 4-way write-back-locking-C L1 VIPT Data cache [ 1.0000000] vfp0 at cpu0: VFP11, rounding, exceptions [ 1.0000000] fclock0 at simplebus2: 19200000 Hz fixed clock (osc) [ 1.0000000] fclock1 at simplebus2: 480000000 Hz fixed clock (otg) [ 1.0000000] simplebus4 at simplebus1 [ 1.0000000] bcmicu0 at simplebus1 [ 1.0000000] bcmcprman0 at simplebus1: BCM283x Clock Controller [ 1.0000000] bcmtmr0 at simplebus1: VC System Timer [ 1.0000000] bcmtmr0: interrupting on icu irq 3 [ 1.0000000] bcmaux0 at simplebus1 [ 1.0000000] /soc/thermal@7e212000 at simplebus1 not configured [ 1.0000000] /soc/dsi@7e209000 at simplebus1 not configured [ 1.0000000] bcmgpio0 at simplebus1: GPIO controller 2835 [ 1.0000000] bcmgpio0: pins 0..31 interrupting on icu irq 49 [ 1.0000000] bcmgpio0: pins 32..54 interrupting on icu irq 50 [ 1.0000000] gpio0 at bcmgpio0: 54 pins [ 1.0000000] bcmdmac0 at simplebus1: DMA0 DMA2 DMA4 DMA5 DMA8 DMA9 DMA10 DMA11 [ 1.0000000] /soc/power at simplebus1 not configured [ 1.0000000] /phy at simplebus0 not configured [ 1.0000000] bsciic0 at simplebus1: Broadcom Serial Controller [ 1.0000000] bsciic0: interrupting on icu irq 53 [ 1.0000000] iic0 at bsciic0: I2C bus [ 1.0000000] bcmpmwdog0 at simplebus1: Power management, Reset and Watchdog controller [ 1.0000000] bcmmbox0 at simplebus1: VC mailbox [ 1.0000000] bcmmbox0: interrupting on icu irq 65 [ 1.0000000] vcmbox0 at bcmmbox0 [ 1.0000000] /soc/txp@7e004000 at simplebus1 not configured [ 1.0000000] plcom0 at simplebus1: ARM PL011 UART [ 1.0000000] plcom0: txfifo disabled [ 1.0000000] plcom0: console [ 1.0000000] plcom0: interrupting on icu irq 57 [ 1.0000000] bcmsdhost0 at simplebus1: SD HOST controller [ 1.0000000] bcmsdhost0: interrupting on icu irq 56 [ 1.0000000] bsciic1 at simplebus1: Broadcom Serial Controller [ 1.0000000] bsciic1: interrupting on icu irq 53 [ 1.0000000] iic1 at bsciic1: I2C bus [ 1.0000000] /soc/pwm@7e20c000 at simplebus1 not configured [ 1.0000000] bsciic2 at simplebus1: Broadcom Serial Controller [ 1.0000000] bsciic2: interrupting on icu irq 53 [ 1.0000000] iic2 at bsciic2: I2C bus [ 1.0000000] /soc/vec@7e806000 at simplebus1 not configured [ 1.0000000] dwctwo0 at simplebus1: USB controller [ 1.0000000] dwctwo0: interrupting on icu irq 9 [ 1.0000000] /soc/hdmi@7e902000 at simplebus1 not configured [ 1.0000000] /soc/gpu at simplebus1 not configured [ 1.0000000] genfb0 at simplebus1Vendor: [INN] [ 1.0000000] Product: [3200] K3A8F HDMI [ 1.0000000] Serial number: 01081620 [ 1.0000000] Manufactured 2016 Week 32 [ 1.0000000] EDID Version 1.3 [ 1.0000000] EDID Comment: [ 1.0000000] Video Input: 80 [ 1.0000000] Digital [ 1.0000000] Gamma: 2.20 [ 1.0000000] Max Size: 70 cm x 39 cm [ 1.0000000] Features: ea [ 1.0000000] DPMS standby [ 1.0000000] DPMS suspend [ 1.0000000] DPMS active-off [ 1.0000000] RGB [ 1.0000000] Preferred timing [ 1.0000000] Chroma Info: [ 1.0000000] Red X: 0.679 [ 1.0000000] Red Y: 0.679 [ 1.0000000] Grn X: 0.206 [ 1.0000000] Grn Y: 0.693 [ 1.0000000] Blu X: 0.151 [ 1.0000000] Blu Y: 0.054 [ 1.0000000] Wht X: 0.313 [ 1.0000000] Wht Y: 0.329 [ 1.0000000] Range: [ 1.0000000] Horizontal: 30 - 83 kHz [ 1.0000000] Vertical: 49 - 72 Hz [ 1.0000000] Max Dot Clock: 170 MHz [ 1.0000000] Video modes: [ 1.0000000] 720x400 @ 70Hz (28320 738 846 900 412 414 449 -H +V) [ 1.0000000] 640x480 @ 60Hz (25175 656 752 800 490 492 525 -H -V) [ 1.0000000] 800x600 @ 60Hz (40000 840 968 1056 601 605 628 +H +V) [ 1.0000000] 1024x768 @ 60Hz (65000 1048 1184 1344 771 777 806 -H -V) [ 1.0000000] 1280x1024 @ 60Hz (108000 1328 1440 1688 1025 1028 1066 +H +V) [ 1.0000000] 1680x1050 @ 60Hz (147140 1784 1968 2256 1051 1054 1087 +H +V) [ 1.0000000] 1920x1080 @ 60Hz (148500 2008 2052 2200 1084 1089 1125 +H +V) [ 1.0000000] 1600x900 @ 60Hz (118996 1696 1864 2128 901 904 932 +H +V) [ 1.0000000] 1440x900 @ 60Hz (106470 1520 1672 1904 901 904 932 +H +V) [ 1.0000000] 1366x768 @ 60Hz (85750 1436 1579 1792 771 774 798 +H +V) [ 1.0000000] Preferred mode: 1920x1080 @ 60Hz [ 1.0000000] Number of extension blocks: 1 [ 1.0000000] rpi_fb_init: addr = 0x5e402000 size = 8355840 [ 1.0000000] rpi_fb_init: depth = 32 [ 1.0000000] rpi_fb_init: pitch = 7680 [ 1.0000000] rpi_fb_init: width = 1920 height = 1080 [ 1.0000000] rpi_fb_init: vwidth = 1920 vheight = 1080 [ 1.0000000] genfb0: framebuffer at 0x5e402000, size 1920x1080, depth 32, stride 7680 [ 1.0000000] wsdisplay0 at genfb0 kbdmux 1 [ 1.0000000] wsmux1: connecting to wsdisplay0 [ 1.0000000] wsdisplay0: screen 0-3 added (default, vt100 emulation) [ 1.0000000] vchiq0 at simplebus1: BCM2835 VCHIQ [ 1.0000000] vchiq0: not supported yet in big-endian mode [ 1.0000000] /arm-pmu at simplebus0 not configured [ 1.0000000] gpioleds0 at simplebus0: ACT [ 1.0000000] bcmrng0 at simplebus1: RNG [ 1.0000000] entropy: ready [ 1.0000000] timecounter: Timecounter "bcmtmr0" frequency 1000000 Hz quality 100 [ 1.0000030] timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0 [ 1.0775170] sdmmc0 at bcmsdhost0 [ 1.0775170] dwctwo0: Core Release: 2.80a (snpsid=4f54280a) [ 1.0775170] usb0 at dwctwo0: USB revision 2.0 [ 1.1677270] uhub0 at usb0: NetBSD (0x0000) DWC2 root hub (0x0000), class 9/0, rev 2.00/1.00, addr 1 [ 1.1831030] uhub0: 1 port with 1 removable, self powered [ 1.1831030] IPsec: Initialized Security Association Processing. [ 1.2060910] aes: BearSSL aes_ct [ 1.2060910] chacha: Portable C ChaCha [ 1.2060910] adiantum: self-test passed [ 1.2182990] aes_ccm: self-test passed [ 1.2182990] blake2s: self-test passed [ 1.2283460] sdmmc0: direct I/O error 5, r=6 p=0xc9b57f14 write [ 1.2684010] sdmmc0: SD card status: 4-bit, C10 [ 1.2785030] ld0 at sdmmc0: <0x03:0x5344:SL16G:0x80:0x14c08797:0x11a> [ 1.2785030] ld0: 15193 MB, 7717 cyl, 64 head, 63 sec, 512 bytes/sect x 31116288 sectors [ 1.2952680] ld0: 4-bit width, High-Speed/SDR25, 50.000 MHz [ 3.0266630] uhub1 at uhub0 port 1: vendor 0424 (0x0424) product 9512 (0x9512), class 9/0, rev 2.00/2.00, addr 2 [ 3.0372110] uhub1: multiple transaction translators [ 3.0372110] uhub1: 3 ports with 2 removable, self powered [ 4.3583870] usmsc0 at uhub1 port 1 [ 4.3583870] usmsc0: vendor 0424 (0x0424) product ec00 (0xec00), rev 2.00/2.00, addr 3 [ 4.3698170] smscphy0 at usmsc0 phy 1: SMSC LAN8700 10/100 Ethernet Transceiver, rev. 3 [ 4.3839290] smscphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto [ 4.3839290] usmsc0: Ethernet address b8:27:eb:c6:55:6b [ 5.3681560] uhub2 at uhub1 port 2: VIA Labs, Inc. (0x2109) USB2.0 Hub (0x2813), class 9/0, rev 2.10/90.11, addr 4 [ 5.3843950] uhub2: single transaction translator [ 5.3843950] uhub2: 4 ports with 4 removable, self powered [ 6.7370650] uhub3 at uhub2 port 2: VIA Labs, Inc. (0x2109) USB2.0 Hub (0x2813), class 9/0, rev 2.10/90.11, addr 5 [ 6.7533200] uhub3: single transaction translator [ 6.7533200] uhub3: 4 ports with 4 removable, self powered [ 8.1259200] uhub4 at uhub3 port 3: Apple Inc. (0x05ac) Keyboard Hub (0x1005), class 9/0, rev 2.00/96.15, addr 6 [ 8.1368050] uhub4: single transaction translator [ 8.1489560] uhub4: 3 ports with 2 removable, bus powered [ 9.5100600] uhidev0 at uhub4 port 2 configuration 1 interface 0 [ 9.5100600] uhidev0: Apple Inc. (0x05ac) Apple Keyboard (0x021d), rev 2.00/0.70, addr 7, iclass 3/1 [ 9.5856740] ukbd0 at uhidev0: 8 Variable keys, 5 Array codes, apple fn key [ 9.9959720] wskbd0 at ukbd0 mux 1 [ 9.9959720] wskbd0: connecting to wsdisplay0 [ 9.9959720] uhidev1 at uhub4 port 2 configuration 1 interface 1 [ 10.0071390] uhidev1: Apple Inc. (0x05ac) Apple Keyboard (0x021d), rev 2.00/0.70, addr 7, iclass 3/0 [ 10.0474240] uhid0 at uhidev1: input=1, output=0, feature=0 [ 11.1283670] uhidev2 at uhub2 port 4 configuration 1 interface 0 [ 11.1395750] uhidev2: vendor 192f (0x192f) USB Optical Mouse (0x0916), rev 2.00/2.00, addr 8, iclass 3/1 [ 11.1501710] ums0 at uhidev2: 3 buttons and Z dir [ 11.1501710] wsmouse0 at ums0 mux 0 [ 12.1310920] umass0 at uhub1 port 3 configuration 1 interface 0 [ 12.1310920] umass0: SanDisk (0x0781) Ultra (0x5581), rev 2.10/1.00, addr 9 [ 12.1472890] umass0: using SCSI over Bulk-Only [ 12.1472890] scsibus0 at umass0: 2 targets, 1 lun per target [ 12.1573090] uhub0: illegal enable change, port 1 [ 12.1573090] sd0 at scsibus0 target 0 lun 0: disk removable [ 12.1701370] sd0: 14663 MB, 29792 cyl, 16 head, 63 sec, 512 bytes/sect x 30031250 sectors [ 12.1801600] crypto: assign driver 0, flags 2 [ 12.1911000] crypto: driver 0 registers alg 1 flags 0 maxoplen 0 [ 12.1911000] crypto: driver 0 registers alg 2 flags 0 maxoplen 0 [ 12.2028950] crypto: driver 0 registers alg 3 flags 0 maxoplen 0 [ 12.2028950] crypto: driver 0 registers alg 4 flags 0 maxoplen 0 [ 12.2147030] crypto: driver 0 registers alg 5 flags 0 maxoplen 0 [ 12.2147030] crypto: driver 0 registers alg 26 flags 0 maxoplen 0 [ 12.2265980] crypto: driver 0 registers alg 27 flags 0 maxoplen 0 [ 12.2265980] crypto: driver 0 registers alg 29 flags 0 maxoplen 0 [ 12.2385790] crypto: driver 0 registers alg 33 flags 0 maxoplen 0 [ 12.2385790] crypto: driver 0 registers alg 17 flags 0 maxoplen 0 [ 12.2505620] crypto: driver 0 registers alg 6 flags 0 maxoplen 0 [ 12.2505620] crypto: driver 0 registers alg 19 flags 0 maxoplen 0 [ 12.2624590] crypto: driver 0 registers alg 7 flags 0 maxoplen 0 [ 12.2624590] crypto: driver 0 registers alg 20 flags 0 maxoplen 0 [ 12.2743530] crypto: driver 0 registers alg 15 flags 0 maxoplen 0 [ 12.2743530] crypto: driver 0 registers alg 24 flags 0 maxoplen 0 [ 12.2863320] crypto: driver 0 registers alg 25 flags 0 maxoplen 0 [ 12.2863320] crypto: driver 0 registers alg 8 flags 0 maxoplen 0 [ 12.2982300] crypto: driver 0 registers alg 21 flags 0 maxoplen 0 [ 12.2982300] crypto: driver 0 registers alg 16 flags 0 maxoplen 0 [ 12.3102110] crypto: driver 0 registers alg 9 flags 0 maxoplen 0 [ 12.3102110] crypto: driver 0 registers alg 10 flags 0 maxoplen 0 [ 12.3221040] crypto: driver 0 registers alg 13 flags 0 maxoplen 0 [ 12.3221040] crypto: driver 0 registers alg 14 flags 0 maxoplen 0 [ 12.3340900] crypto: driver 0 registers alg 28 flags 0 maxoplen 0 [ 12.3340900] crypto: driver 0 registers alg 30 flags 0 maxoplen 0 [ 12.3460670] crypto: driver 0 registers alg 31 flags 0 maxoplen 0 [ 12.3460670] crypto: driver 0 registers alg 32 flags 0 maxoplen 0 [ 12.3580490] crypto: driver 0 registers alg 11 flags 0 maxoplen 0 [ 12.3580490] crypto: driver 0 registers alg 18 flags 0 maxoplen 0 [ 12.3700320] crypto: driver 0 registers alg 23 flags 0 maxoplen 0 [ 12.3700320] crypto: driver 0 registers alg 22 flags 0 maxoplen 0 [ 12.3820130] cgd: self-test aes-xts-256 [ 12.3820130] cgd: self-test aes-xts-512 [ 12.3820130] cgd: self-test aes-cbc-128 [ 12.3932160] cgd: self-test aes-cbc-256 [ 12.3932160] cgd: self-test 3des-cbc-192 [ 12.3932160] cgd: self-test blowfish-cbc-448 [ 12.4049390] cgd: self-test aes-cbc-128 (encblkno8) [ 12.4049390] cgd: self-tests passed [ 12.4249890] WARNING: 2 errors while detecting hardware; check system log. [ 12.4378130] boot device: sd0 [ 12.4378130] root on sd0a dumps on sd0b [ 12.4478340] root file system type: ffs [ 12.4601370] kern.module.path=/stand/evbarm/9.99.74/modules [ 12.4601370] WARNING: no TOD clock present [ 12.4601370] WARNING: using filesystem time [ 12.4737590] WARNING: CHECK AND RESET THE DATE! Enter pathname of shell or RETURN for /bin/sh: We recommend that you create a non-root account and use su(1) for root access. # exit Fri Oct 30 19:57:32 JST 2020 Starting root file system check: /dev/rsd0a: file system is clean; not checking swapctl: setting dump device to /dev/sd0b swapctl: adding /dev/sd0b as swap device at priority 0 Starting file system checks: /dev/rld0e: 23 files, 45124 free (11281 clusters) Loaded entropy from /var/db/entropy-file. Setting tty flags. Setting sysctl variables: ddb.onpanic: 1 -> 0 Starting network. Hostname: rpi1b IPv6 mode: host Configuring network interfaces: usmsc0. Adding interface aliases:. add net default: gateway 192.168.10.1 Waiting for duplicate address detection to finish... Building databases: dev, utmp, utmpx. wsconscfg: screen 1 is already configured wsconscfg: screen 2 is already configured wsconscfg: screen 3 is already configured [ 29.2913590] wsdisplay0: screen 4 added (default, vt100 emulation) Starting syslogd. Setting date via ntp. Mounting all file systems... Clearing temporary files. Updating fontconfig cache: done. Setting securelevel: kern.securelevel: 0 -> 1 swapctl: setting dump device to /dev/sd0b Starting virecover. Checking for core dump... savecore: no core dump Starting local daemons:. Updating motd. Starting ntpd. Starting sshd. Starting postfix. Starting inetd. Starting cron. Fri Oct 30 19:58:40 JST 2020 NetBSD/evbarm (rpi1b) (constty) login: rin Password: Oct 30 19:59:03 rpi1b login: rin on tty constty Last login: Fri Oct 30 19:48:21 2020 from 192.168.10.4 on pts/1 Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017, 2018, 2019, 2020 The NetBSD Foundation, Inc. All rights reserved. Copyright (c) 1982, 1986, 1989, 1991, 1993 The Regents of the University of California. All rights reserved. NetBSD 9.99.74 (RPI0EB) #47: Fri Oct 30 19:54:04 JST 2020 Welcome to NetBSD! We recommend that you create a non-root account and use su(1) for root access. rpi1b$ uname -ap NetBSD rpi1b 9.99.74 NetBSD 9.99.74 (RPI0EB) #47: Fri Oct 30 19:54:04 JST 2020 rin@latipes:/sys/arch/evbarm/compile/RPI0EB evbarm earmv6hfeb rpi1b$