[0000.159] [L4T TegraBoot] (version 00.00.2018.01-l4t-c536fca9) [0000.165] Processing in cold boot mode Bootloader 2 [0000.170] A02 Bootrom Patch rev = 1023 [0000.173] Power-up reason: software reset [0000.177] No Battery Present [0000.179] pmic max77620 reset reason [0000.183] pmic max77620 NVERC : 0x0 [0000.186] RamCode = 0 [0000.188] Platform has DDR4 type RAM [0000.192] max77620 disabling SD1 Remote Sense [0000.196] Setting DDR voltage to 1125mv [0000.200] Serial Number of Pmic Max77663: 0x30ce1 [0000.207] Entering ramdump check [0000.210] Get RamDumpCarveOut = 0x0 [0000.214] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.219] Last reboot was clean, booting normally! [0000.223] Sdram initialization is successful [0000.228] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000 [0000.234] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000 [0000.239] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000 [0000.245] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000 [0000.251] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000 [0000.257] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000 [0000.263] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000 [0000.269] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000 [0000.285] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000 [0000.291] Platform-DebugCarveout: 0 [0000.294] Nck Carveout Base=0x00000000ff080000 Size=0x00200000 [0000.300] Non secure mode, and RB not enabled. [0000.304] Read GPT from (4:0) [0000.614] Csd NumOfBlocks=250085376 [0000.619] Set High speed to 1 [0000.628] Using GPT Primary to query partitions [0000.633] Loading Tboot-CPU binary [0000.643] Verifying TBC in OdmNonSecureSBK mode [0000.653] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.660] Bootloader downloaded successfully. [0000.664] Downloaded Tboot-CPU binary to 0xa0000258 [0000.669] MAX77620_GPIO5 configured [0000.672] CPU power rail is up [0000.675] CPU clock enabled [0000.679] Performing RAM repair [0000.682] Updating A64 Warmreset Address to 0xa00002e9 [0000.687] Loading NvTbootBootloaderDTB [0000.711] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode [0000.784] Bootloader DTB Load Address: 0x83000000 [0000.789] Loading NvTbootKernelDTB [0000.813] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode [0000.885] Kernel DTB Load Address: 0x83100000 [0000.890] Loading cboot binary [0000.920] Verifying EBT in OdmNonSecureSBK mode [0000.961] Bootloader load address is 0x92c00000, entry address is 0x92c00258 [0000.968] Bootloader downloaded successfully. [0000.973] Read PT from (2:0) [0000.988] Using BFS PT to query partitions [0000.992] PT: Partition NCT NOT found ! [0000.996] Warning: Find Partition via PT Failed [0001.000] Next binary entry address: 0x92c00258 [0001.005] BoardId: 3448 [0001.009] Overriding pmu board id with proc board id [0001.014] Display board id is not available [0001.042] Verifying SC7EntryFw in OdmNonSecureSBK mode [0001.099] /bpmp deleted [0001.101] SC7EntryFw header found loaded at 0xff700000 [0001.296] OVR2 PMIC [0001.298] Bpmp FW successfully loaded [0001.302] WB0 init successfully at 0xff780000 [0001.306] Set NvDecSticky Bits [0001.310] GSC2 address ff53fffc value c0edbbcc [0001.316] GSC MC Settings done [0001.320] TOS Image length 53680 [0001.323] Monitor size 53680 [0001.325] OS size 0 [0001.333] Secure Os AES-CMAC Verification Success! [0001.337] TOS image cipher info: plaintext [0001.341] Loading and Validation of Secure OS Successful [0001.357] SC7 Entry Firmware - 0xff700000, 0x4000 [0001.362] NvTbootPackSdramParams: start. [0001.367] NvTbootPackSdramParams: done. [0001.371] Tegraboot started after 87465 us [0001.374] Basic modules init took 955968 us [0001.378] Sec Bootdevice Read Time = 12 ms, Read Size = 65 KB [0001.384] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB [0001.389] Storage Device Read Time = 109 ms, Read Size = 2241 KB [0001.395] Storage Device Write Time = 0 ms, Write Size = 0 KB [0001.401] Next stage binary read took 24429 us [0001.405] Carveout took -36121 us [0001.408] CPU initialization took 372072 us [0001.412] Total time taken by TegraBoot 1316348 us [0001.417] Starting CPU & Halting co-processor 64NOTICE: BL31: v1.3(release):de895fd9e NOTICE: BL31: Built : 12:23:48, Oct 16 2020 ERROR: Error initializing runtime service trusty_fast [0001.539] RamCode = 0 [0001.544] LPDDR4 Training: Read DT: Number of tables = 2 [0001.549] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.562] EMC Training Successful [0001.565] 408000 not found in DVFS table [0001.571] RamCode = 0 [0001.575] DT Write: emc-table@204000 succeeded [0001.580] DT Write: emc-table@1600000 succeeded [0001.584] LPDDR4 Training: Write DT: Number of tables = 2 [0001.631] [0001.632] Debug Init done [0001.635] Marked DTB cacheable [0001.638] Bootloader DTB loaded at 0x83000000 [0001.643] Marked DTB cacheable [0001.645] Kernel DTB loaded at 0x83100000 [0001.649] DeviceTree Init done [0001.662] Pinmux applied successfully [0001.667] gicd_base: 0x50041000 [0001.670] gicc_base: 0x50042000 [0001.673] Interrupts Init done [0001.677] Using base:0x60005090 & irq:208 for tick-timer [0001.682] Using base:0x60005098 for delay-timer [0001.687] platform_init_timer: DONE [0001.690] Timer(tick) Init done [0001.694] osc freq = 38400 khz [0001.698] [0001.699] Welcome to L4T Cboot [0001.702] [0001.703] Cboot Version: 00.00.2018.01-t210-4686ce50 [0001.708] calling constructors [0001.711] initializing heap [0001.714] initializing threads [0001.717] initializing timers [0001.720] creating bootstrap completion thread [0001.724] top of bootstrap2() [0001.727] CPU: ARM Cortex A57 [0001.730] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0001.734] initializing platform [0001.742] Manufacturer: MF = 0xc2, ID MSB = 0x25 [0001.746] ID LSB = 0x36, ID-CFI len = 194 bytes [0001.751] Macronix QSPI chip present [0001.754] SPI device register [0001.757] init boot device [0001.760] allocating memory for boot device(SPI) [0001.764] registering boot device [0001.779] sdmmc node status = okay [0001.782] sdcard instance = 0 [0001.785] sdcard gpio handle 0x5b [0001.788] sdcard gpio pin 0xc9 [0001.791] sdcard gpio flags 0x0 [0001.794] vmmc-supply 0x9e [0001.797] Instance: 0 [0001.799] Allocating memory for context [0001.803] enabling clock [0001.805] sd card init [0001.807] Check card present and stable [0001.811] Send command 0 [0001.828] Send command 3 [0001.832] Set RCA for the card [0001.835] Query card specific data by command 9 [0001.841] Parse CSD data [0001.844] Send command 7 [0001.854] Calling sd device register [0001.857] Init sdcard [0001.860] Allocating memory for boot device [0001.864] Registering user device [0001.877] Enable APE clock [0001.879] Un-powergate APE partition [0001.883] of_register: registering tegra_udc to of_hal [0001.888] of_register: registering inv20628-driver to of_hal [0001.894] of_register: registering ads1015-driver to of_hal [0001.899] of_register: registering lp8557-bl-driver to of_hal [0001.905] of_register: registering bq2419x_charger to of_hal [0001.911] of_register: registering bq27441_fuel_gauge to of_hal [0001.922] gpio framework initialized [0001.926] of_register: registering tca9539_gpio to of_hal [0001.931] of_register: registering tca9539_gpio to of_hal [0001.936] of_register: registering i2c_bus_driver to of_hal [0001.942] of_register: registering i2c_bus_driver to of_hal [0001.948] of_register: registering i2c_bus_driver to of_hal [0001.953] pmic framework initialized [0001.957] of_register: registering max77620_pmic to of_hal [0001.962] regulator framework initialized [0001.966] of_register: registering tps65132_bl_driver to of_hal [0001.972] initializing target [0001.978] gpio_driver_register: register 'tegra_gpio_driver' driver [0001.986] board ID = D78, board SKU = 0 [0001.989] Skipping Z3! [0001.994] fixed regulator driver initialized [0002.012] initializing OF layer [0002.015] NCK carveout not present [0002.018] Skipping dts_overrides [0002.023] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.039] I2C Bus Init done [0002.042] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.052] I2C Bus Init done [0002.055] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.065] I2C Bus Init done [0002.068] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.078] I2C Bus Init done [0002.081] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.092] I2C Bus Init done [0002.094] of_children_init: Ops found for compatible string maxim,max77620 [0002.105] max77620_init using irq 118 [0002.109] register 'maxim,max77620' pmic [0002.114] gpio_driver_register: register 'max77620-gpio' driver [0002.120] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.130] I2C Bus Init done [0002.134] NCK carveout not present [0002.144] Find /i2c@7000c000's alias i2c0 [0002.148] get eeprom at 1-a0, size 256, type 0 [0002.156] Find /i2c@7000c500's alias i2c2 [0002.160] get eeprom at 3-a0, size 256, type 0 [0002.165] get eeprom at 3-ae, size 256, type 0 [0002.169] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.174] I2C slave not started [0002.177] I2C write failed [0002.180] Writing offset failed [0002.183] eeprom_init: EEPROM read failed [0002.187] pm_ids_update: eeprom init failed [0002.191] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.221] pm_ids_update: The pm board id is 3448-0000-200 [0002.228] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50 [0002.236] pm_ids_update: pm id update successful [0002.241] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.271] pm_ids_update: The pm board id is 3449-0000-200 [0002.277] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57 [0002.285] pm_ids_update: pm id update successful [0002.316] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.322] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0002.330] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.335] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0002.344] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e5:16:1b [0002.350] Plugin Manager: Parse ODM data 0x00094000 [0002.362] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 [0002.377] Find /i2c@7000c000's alias i2c0 [0002.381] get eeprom at 1-a0, size 256, type 0 [0002.390] Find /i2c@7000c500's alias i2c2 [0002.394] get eeprom at 3-a0, size 256, type 0 [0002.398] get eeprom at 3-ae, size 256, type 0 [0002.403] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.408] I2C slave not started [0002.411] I2C write failed [0002.414] Writing offset failed [0002.417] eeprom_init: EEPROM read failed [0002.421] pm_ids_update: eeprom init failed [0002.425] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.455] pm_ids_update: The pm board id is 3448-0000-200 [0002.461] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50 [0002.468] pm_ids_update: pm id update successful [0002.473] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.503] pm_ids_update: The pm board id is 3449-0000-200 [0002.509] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57 [0002.516] pm_ids_update: pm id update successful [0002.546] Add serial number:1421919051417 as DT property [0002.554] Applying platform configs [0002.561] platform-init is not present. Skipping [0002.565] calling apps_init() [0002.590] Found 14 GPT partitions in "sd0" [0002.594] Proceeding to Cold Boot [0002.597] starting app android_boot_app [0002.601] Device state: unlocked [0002.604] display console init [0002.613] could not find regulator [0002.616] hdmi cable connected [0002.631] edid read success [0002.647] edid read success [000[0002.653] DT entry for leds-pwm not found 2.649] width = 640, height = 480, frequency = 25174825 [0002.662] width = 1920, height = 1080, frequency = 148500000 [0002.667] width = 1366, height = 768, frequency = 85750000 [0002.673] width = 1920, height = 1080, frequency = 148500000 [0002.679] width = 1920, height = 1080, frequency = 148351648 [0002.684] width = 1280, height = 720, frequency = 74175824 [0002.690] width = 720, height = 480, frequency = 26973026 [0002.695] width = 720, height = 480, frequency = 26973026 [0002.700] width = 640, height = 480, frequency = 25174825 [0002.706] width = 1920, height = 1080, frequency = 148351648 [0002.711] width = 720, height = 576, frequency = 26973026 [0002.717] width = 1280, height = 720, frequency = 74175824 [0002.722] width = 1920, height = 1080, frequency = 74175824 [0002.728] width = 720, height = 576, frequency = 26973026 [0002.733] Best mode Width = 1920, Height = 1080, freq = 148351648 [0002.741] tmds-config node not found [0002.745] pmc_set_io_pad_voltage: Error -2 retrieving platform-io-pad-voltagepropsetting 'avdd-io-hdmi-dp' regulator to 1050000 micro volts [0002.760] setting 'vdd-1v8' regulator to 1800000 micro volts [0002.767] could not find regulator [0002.771] could not find regulator [0002.774] could not find regulator [0002.802] using default cmu settings [0002.806] dc_hdmi_enable, starting HDMI initialisation [0002.812] dc_hdmi_enable, HDMI initialisation complete [0002.817] list and configure display window [0002.826] display console init completed [0002.837] subnode volume_up is not found ! [0002.841] subnode back is not found ! [0002.845] subnode volume_down is not found ! [0002.849] subnode menu is not found ! [0002.852] Gpio keyboard init success [0002.896] found decompressor handler: lz4-legacy [0002.911] decompressing blob (type 1)... [0002.946] load_bmp_blob: panelresolution=1080 type=3 [0002.997] decompressor handler not found [0003.001] load_firmware_blob: Firmware blob loaded, entries=2 [0003.006] -------> se_aes_verify_sbk_clear: 747 [0003.011] se_aes_verify_sbk_clear: Error [0003.015] bl_battery_charging: connected to external power supply [0003.022] xusb is supported [0003.028] error while finding nvidia,portmap [0003.532] xusb blob version 0 size 124416 [0003.536] firmware size 124416 [0003.541] Firmware timestamp: 0x5da88fc3, Version: 50.25 release [0003.550] xhci0: 64 bytes context size, 32-bit DMA [0003.590] usbus0: 5.0Gbps Super Speed USB v3.0 [0003.610] uhub0: on usbus0 [0004.260] uhub0: 9 ports with 9 removable, self powered [0005.260] failed to get HID devices [0005.263] failed to init xhci or no usb device attached [0005.273] device_query_partition_size: failed to open partition sd0:MSC ! [0005.280] MSC Partition not found [0005.286] device_query_partition_size: failed to open partition sd0:USP ! [0005.293] USP partition read failed! [0005.296] blob_init: blob-partition USP header read failed [0005.302] android_boot Unable to update recovery partition [0005.307] kfs_getpartname: name = LNX [0005.311] Loading kernel from LNX [0005.410] load kernel from storage [0005.421] decompressor handler not found [0005.479] Successfully loaded kernel and ramdisk images [0005.485] load_bmp_blob: panelresolution=1080 type=3 [0005.981] display bmp image done [0005.984] NCK carveout not present [0005.988] Skipping dts_overrides [0005.991] NCK carveout not present [0006.000] Find /i2c@7000c000's alias i2c0 [0006.004] get eeprom at 1-a0, size 256, type 0 [0006.013] Find /i2c@7000c500's alias i2c2 [0006.017] get eeprom at 3-a0, size 256, type 0 [0006.021] get eeprom at 3-ae, size 256, type 0 [0006.026] pm_ids_update: Updating 1,a0, size 256, type 0 [0006.031] I2C slave not started [0006.034] I2C write failed [0006.037] Writing offset failed [0006.040] eeprom_init: EEPROM read failed [0006.044] pm_ids_update: eeprom init failed [0006.048] pm_ids_update: Updating 3,a0, size 256, type 0 [0006.078] pm_ids_update: The pm board id is 3448-0000-200 [0006.085] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50 [0006.093] pm_ids_update: pm id update successful [0006.098] pm_ids_update: Updating 3,ae, size 256, type 0 [0006.128] pm_ids_update: The pm board id is 3449-0000-200 [0006.134] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57 [0006.142] pm_ids_update: pm id update successful [0006.173] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0006.179] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0006.186] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0006.192] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0006.201] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e5:16:1b [0006.207] Plugin Manager: Parse ODM data 0x00094000 [0006.219] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 [0006.228] Add serial number:1421919051417 as DT property [0006.237] "bpmp" doesn't exist, creating [0006.242] Updated bpmp info to DTB [0006.247] Updated initrd info to DTB [0006.251] "proc-board" doesn't exist, creating [0006.257] Updated board info to DTB [0006.260] "pmu-board" doesn't exist, creating [0006.266] Updated board info to DTB [0006.269] "display-board" doesn't exist, creating [0006.275] Updated board info to DTB [0006.279] "reset" doesn't exist, creating [0006.283] Updated reset info to DTB [0006.287] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,2 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1125 core_edp_ma=4000 tegra_fbmem=0x800000@0x92cb4000 is_hdmi_initialised=1 [0006.326] DTB cmdline: earlycon=uart8250,mmio32,0x70006000 [0006.331] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [0006.344] Updated bootarg info to DTB [0006.348] Adding uuid 00000001644226c82000000005008240 to DT [0006.354] Adding eks info 0 to DT [0006.360] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7 [0006.366] Updated memory info to DTB [0006.371] Updated system-lp0-disable info to DTB [0006.379] set vdd_core voltage to 1125 mv [0006.383] setting 'vdd-core' regulator to 1125000 micro volts [0006.400] Found secure-pmc; disable BPMP U-Boot 2016.07-g7a7e3f476e (Oct 16 2020 - 12:23:42 -0700) TEGRA210 Model: NVIDIA P3450-Porg Board: NVIDIA P3450-PORG DRAM: 4 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 SF: Detected MX25U3235F with page size 256 Bytes, erase size 4 KiB, total 4 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc1 is current device Scanning mmc 1:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 908 bytes read in 177 ms (4.9 KiB/s) 1: primary kernel Retrieving file: /boot/netbsd.img 18587888 bytes read in 1000 ms (17.7 MiB/s) append: root=sd0a console=fb ## Flattened Device Tree blob at 83100000 Booting using the fdt blob at 0x83100000 reserving fdt memory region: addr=80000000 size=20000 Using Device Tree in place at 0000000083100000, end 000000008317de85 Starting kernel ... [ 1.0000000] NetBSD/evbarm (fdt) booting ... [ 1.0000000] Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, [ 1.0000000] 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017, [ 1.0000000] 2018, 2019, 2020 The NetBSD Foundation, Inc. All rights reserved. [ 1.0000000] Copyright (c) 1982, 1986, 1989, 1991, 1993 [ 1.0000000] The Regents of the University of California. All rights reserved. [ 1.0000000] NetBSD 9.99.74 (GENERIC64) #82: Sun Oct 25 17:17:55 JST 2020 [ 1.0000000] rin@latipes:/usr/src/sys/arch/evbarm/compile/GENERIC64 [ 1.0000000] total memory = 4044 MB [ 1.0000000] avail memory = 3918 MB [ 1.0000000] entropy: no seed from bootloader [ 1.0000000] armfdt0 (root) [ 1.0000000] simplebus0 at armfdt0: NVIDIA Jetson Nano Developer Kit [ 1.0000000] simplebus1 at simplebus0 [ 1.0000000] cpus0 at simplebus0 [ 1.0000000] simplebus2 at simplebus0 [ 1.0000000] simplebus3 at simplebus0 [ 1.0000000] simplebus4 at simplebus0 [ 1.0000000] simplebus5 at simplebus0 [ 1.0000000] psci0 at simplebus0: PSCI 1.0 [ 1.0000000] simplebus6 at simplebus0 [ 1.0000000] simplebus7 at simplebus0 [ 1.0000000] simplebus8 at simplebus4 [ 1.0000000] tegralic0 at simplebus0: LIC [ 1.0000000] gic0 at simplebus0: GIC [ 1.0000000] armgic0 at gic0: Generic Interrupt Controller, 224 sources (212 valid) [ 1.0000000] armgic0: 16 Priorities, 191 SPIs, 6 PPIs, 15 SGIs [ 1.0000000] gtmr0 at simplebus0: Generic Timer [ 1.0000000] gtmr0: interrupting on GIC irq 27 [ 1.0000000] armgtmr0 at gtmr0: Generic Timer (19200 kHz, virtual) [ 1.0000030] tegragpio0 at simplebus0: GPIO [ 1.0000030] gpio0 at tegragpio0 (A): 8 pins [ 1.0000030] gpio1 at tegragpio0 (B): 8 pins [ 1.0000030] gpio2 at tegragpio0 (C): 8 pins [ 1.0000030] gpio3 at tegragpio0 (D): 8 pins [ 1.0000030] gpio4 at tegragpio0 (E): 8 pins [ 1.0000030] gpio5 at tegragpio0 (F): 8 pins [ 1.0000030] gpio6 at tegragpio0 (G): 8 pins [ 1.0000030] gpio7 at tegragpio0 (H): 8 pins [ 1.0000030] gpio8 at tegragpio0 (I): 8 pins [ 1.0000030] gpio9 at tegragpio0 (J): 8 pins [ 1.0000030] gpio10 at tegragpio0 (K): 8 pins [ 1.0000030] gpio11 at tegragpio0 (L): 8 pins [ 1.0000030] gpio12 at tegragpio0 (M): 8 pins [ 1.0000030] gpio13 at tegragpio0 (N): 8 pins [ 1.0000030] gpio14 at tegragpio0 (O): 8 pins [ 1.0000030] gpio15 at tegragpio0 (P): 8 pins [ 1.0000030] gpio16 at tegragpio0 (Q): 8 pins [ 1.0000030] gpio17 at tegragpio0 (R): 8 pins [ 1.0000030] gpio18 at tegragpio0 (S): 8 pins [ 1.0000030] gpio19 at tegragpio0 (T): 8 pins [ 1.0000030] gpio20 at tegragpio0 (U): 8 pins [ 1.0000030] gpio21 at tegragpio0 (V): 8 pins [ 1.0000030] gpio22 at tegragpio0 (W): 8 pins [ 1.0000030] gpio23 at tegragpio0 (X): 8 pins [ 1.0000030] gpio24 at tegragpio0 (Y): 8 pins [ 1.0000030] gpio25 at tegragpio0 (Z): 8 pins [ 1.0000030] gpio26 at tegragpio0 (AA): 8 pins [ 1.0000030] gpio27 at tegragpio0 (BB): 8 pins [ 1.0000030] gpio28 at tegragpio0 (CC): 8 pins [ 1.0000030] gpio29 at tegragpio0 (DD): 8 pins [ 1.0000030] gpio30 at tegragpio0 (EE): 8 pins [ 1.0000030] tegra210car0 at simplebus0: CAR [ 1.0000030] tegrai2c0 at simplebus0: I2C [ 1.0000030] tegrai2c0: interrupting on irq 85 [ 1.0000030] iic0 at tegrai2c0: I2C bus [ 1.0000030] max77620pmic0 at iic0 addr 0x3c: MAX77620 Power Management IC [ 1.0000030] tegrapmc0 at simplebus0: PMC [ 1.0000030] fregulator0 at simplebus2: vdd-usb-vbus [ 1.0000030] fregulator1 at simplebus2: vdd-ac-bat [ 1.0000030] fregulator2 at simplebus2: vdd-usb-vbus2 [ 1.0000030] fregulator3 at simplebus2: vdd-5v0-hdmi [ 1.0000030] tegrai2c1 at simplebus0: I2C [ 1.0000030] tegrai2c1: interrupting on irq 152 [ 1.0000030] iic1 at tegrai2c1: I2C bus [ 1.0000030] fregulator4 at simplebus2: vdd-5v0-sys [ 1.0000030] fregulator5 at simplebus2: vdd-1v8-sys [ 1.0000030] fregulator6 at simplebus2: vdd-fan [ 1.0000030] tegrai2c2 at simplebus0: I2C [ 1.0000030] tegrai2c2: interrupting on irq 70 [ 1.0000030] iic2 at tegrai2c2: I2C bus [ 1.0000030] titemp0 at iic2 addr 0x4c: TMP451 [ 1.0000030] tegrai2c3 at simplebus0: I2C [ 1.0000030] tegrai2c3: interrupting on irq 124 [ 1.0000030] iic3 at tegrai2c3: I2C bus [ 1.0000030] iic3: WARNING: ignoring bad device address @ 0xc0ffff [ 1.0000030] tegrai2c4 at simplebus0: I2C [ 1.0000030] tegrai2c4: interrupting on irq 116 [ 1.0000030] iic4 at tegrai2c4: I2C bus [ 1.0000030] i2cmux at iic4 addr 0x70 not configured [ 1.0000030] gpio at iic4 addr 0x20 not configured [ 1.0000030] icm20628 at iic4 addr 0x68 not configured [ 1.0000030] ak8963 at iic4 addr 0x0d not configured [ 1.0000030] cm32180 at iic4 addr 0x48 not configured [ 1.0000030] iqs263 at iic4 addr 0x48 not configured [ 1.0000030] rt5659.1-001a at iic4 addr 0x1a not configured [ 1.0000030] com0 at simplebus0: Tegra UART, 8-byte FIFO [ 1.0000030] com0: console [ 1.0000030] com0: interrupting on irq 68 [ 1.0000030] tegrai2c5 at simplebus0: I2C [ 1.0000030] tegrai2c5: interrupting on irq 95 [ 1.0000030] iic5 at tegrai2c5: I2C bus [ 1.0000030] tegrafuse0 at simplebus0: couldn't get reset fuse [ 1.0000030] /tegra-aotag at simplebus0 not configured [ 1.0000030] /dvfs_rails/vdd-gpu-scaling-cdev@7 at simplebus1 not configured [ 1.0000030] /dvfs_rails/vdd-gpu-vmax-cdev@9 at simplebus1 not configured [ 1.0000030] /core_dvfs_cdev_floor at simplebus0 not configured [ 1.0000030] /core_dvfs_cdev_cap at simplebus0 not configured [ 1.0000030] /dfll-cdev-floor at simplebus0 not configured [ 1.0000030] /soctherm@0x700E2000 at simplebus0 not configured [ 1.0000030] /cpu-throttle-alert at simplebus0 not configured [ 1.0000030] /bthrot_cdev at simplebus0 not configured [ 1.0000030] /dfll-cdev-cap at simplebus0 not configured [ 1.0000030] /gpu-throttle-alert at simplebus0 not configured [ 1.0000030] /hot-surface-alert at simplebus0 not configured [ 1.0000030] /external-memory-controller@7001b000 at simplebus0 not configured [ 1.0000030] /power-domain at simplebus0 not configured [ 1.0000030] /clock@70110000 at simplebus0 not configured [ 1.0000030] /iommu at simplebus0 not configured [ 1.0000030] /aconnect@702c0000 at simplebus0 not configured [ 1.0000030] tegrapinmux0 at simplebus0: Pinmux [ 1.0000030] tegra210xpad0 at simplebus0: XUSB PADCTL [ 1.0000030] tegra210xphy0 at tegra210xpad0: usb2-0 [ 1.0000030] tegra210xphy1 at tegra210xpad0: usb2-1 [ 1.0000030] tegra210xphy2 at tegra210xpad0: usb2-2 [ 1.0000030] tegra210xphy3 at tegra210xpad0: pcie-0 [ 1.0000030] tegra210xphy4 at tegra210xpad0: pcie-1 [ 1.0000030] tegra210xphy5 at tegra210xpad0: pcie-2 [ 1.0000030] tegra210xphy6 at tegra210xpad0: pcie-3 [ 1.0000030] tegra210xphy7 at tegra210xpad0: pcie-4 [ 1.0000030] tegra210xphy8 at tegra210xpad0: pcie-5 [ 1.0000030] tegra210xphy9 at tegra210xpad0: pcie-6 [ 1.0000030] tegra210xpad0: port usb2-0: set mode otg, external [ 1.0000030] tegra210xpad0: port usb2-1: set mode host, external [ 1.0000030] tegra210xpad0: port usb2-2: set mode host, external [ 1.0000030] tegra210xpad0: port usb3-0: set companion usb2-1, external [ 1.0000030] /mailbox@70098000 at simplebus0 not configured [ 1.0000030] /regulators/regulator@2 at simplebus2 not configured [ 1.0000030] /extcon/extcon@1 at simplebus3 not configured [ 1.0000030] /dma@60020000 at simplebus0 not configured [ 1.0000030] spdiftx0 at simplebus0: SPDIF transmitter [ 1.0000030] spdiftx1 at simplebus0: SPDIF transmitter [ 1.0000030] spdiftx2 at simplebus0: SPDIF transmitter [ 1.0000030] spdiftx3 at simplebus0: SPDIF transmitter [ 1.0000030] /host1x/sor1 at simplebus4 not configured [ 1.0000030] /regulators/regulator@4 at simplebus2 not configured [ 1.0000030] /host1x/sor at simplebus4 not configured [ 1.0000030] /host1x/dpaux at simplebus4 not configured [ 1.0000030] /host1x/dpaux1 at simplebus4 not configured [ 1.0000030] /regulators/regulator@3 at simplebus2 not configured [ 1.0000030] /pwm_regulators/pwm-regulator@0 at simplebus5 not configured [ 1.0000030] /smp-custom-ipi at simplebus0 not configured [ 1.0000030] /pwm@7000a000 at simplebus0 not configured [ 1.0000030] /host1x/i2c@546c0000 at simplebus4 not configured [ 1.0000030] /sound at simplebus0 not configured [ 1.0000030] sdhc0 at simplebus0: SDMMC (81600 kHz) [ 1.0000030] sdhc0: interrupting on irq 46 [ 1.0000030] sdhc0: SDHC 4.0, rev 3, 32-bit ADMA2, 81600 kHz, HS 1.8V 3.0V 3.3V, re-tuning mode 1, 512 byte blocks [ 1.0000030] sdmmc0 at sdhc0 slot 0 [ 1.0000030] /regulators/regulator@9 at simplebus2 not configured [ 1.0000030] /tegra-camera-platform at simplebus0 not configured [ 1.0000030] tegrapcie0 at simplebus0: PCIE [ 1.0000030] tegrapcie0: interrupting on irq 130 [ 1.0000030] tegrapcie0: lane config: x4 x1 [ 1.0000030] panic: trap_el1h_error [ 1.0000030] cpu0: Begin traceback... [ 1.0000030] trace fp ffffc000011c23b0 [ 1.0000030] fp ffffc000011c23e0 vpanic() at ffffc0000051692c netbsd:vpanic+0x14c [ 1.0000030] fp ffffc000011c2440 panic() at ffffc00000516a24 netbsd:panic+0x44 [ 1.0000030] fp ffffc000011c24d0 trap_el1h_error() at ffffc000000a0c1c netbsd:trap_el1h_error+0x1c [ 1.0000030] tf ffffc000011c24e0 el1_trap() at ffffc000000a2f84 netbsd:el1_trap [ 1.0000030] ---- trapframe 0xffffc000011c24e0 (304 bytes) ---- [ 1.0000030] pc=ffffc000000bffb4, spsr=0000000080000005 [ 1.0000030] esr=00000000bf000000, far=0000000000000000 [ 1.0000030] x0=000000000000ffff, x1=0000000000010000 [ 1.0000030] x2=000000000000000c, x3=ffffc00003d76038 [ 1.0000030] x4=000000000000002a, x5=0000000000000000 [ 1.0000030] x6=0000000000002498, x7=0000010000000000 [ 1.0000030] x8=0000000000000000, x9=0000000000000006 [ 1.0000030] x10=0000000000000040, x11=000000000000003f [ 1.0000030] x12=ffffff00000d00c0, x13=ffffff00000d0153 [ 1.0000030] x14=0000000000000000, x15=ffffc000034054e8 [ 1.0000030] x16=ffffc000000949c8, x17=1a1d7f3851218c40 [ 1.0000030] x18=0000000000001000, x19=0000000000010000 [ 1.0000030] x20=0000000000000000, x21=ffffc00003406000 [ 1.0000030] x22=ffffc00000ea8298, x23=0000000000000000 [ 1.0000030] x24=0000000000000000, x25=ffffc00003404560 [ 1.0000030] x26=ffffc00003403000, x27=0000000000000001 [ 1.0000030] x28=0000000000100000, fp=x29=ffffc000011c2810 [ 1.0000030] lr=x30=ffffc000000bff88, sp=ffffc000011c2810 [ 1.0000030] ------------------------------------------------ [ 1.0000030] fp ffffc000011c2810 probe_bus() at ffffc000000bffb4 netbsd:probe_bus+0x104 [ 1.0000030] fp ffffc000011c28e0 probe_bus() at ffffc000000c0b2c netbsd:probe_bus+0xc7c [ 1.0000030] fp ffffc000011c29b0 pci_configure_bus() at ffffc000000c2158 netbsd:pci_configure_bus+0xe0 [ 1.0000030] fp ffffc000011c29f0 tegra_pcie_attach() at ffffc000000375e0 netbsd:tegra_pcie_attach+0x680 [ 1.0000030] fp ffffc000011c2b60 config_attach_loc() at ffffc000004fa4dc netbsd:config_attach_loc+0x184 [ 1.0000030] fp ffffc000011c2bb0 fdt_rescan() at ffffc0000061773c netbsd:fdt_rescan+0x1f4 [ 1.0000030] fp ffffc000011c2d30 config_attach_loc() at ffffc000004fa4dc netbsd:config_attach_loc+0x184 [ 1.0000030] fp ffffc000011c2d80 arm_fdt_attach() at ffffc00000065828 netbsd:arm_fdt_attach+0x90 [ 1.0000030] fp ffffc000011c2de0 config_attach_loc() at ffffc000004fa4dc netbsd:config_attach_loc+0x184 [ 1.0000030] fp ffffc000011c2e30 cpu_configure() at ffffc00000061448 netbsd:cpu_configure+0x40 [ 1.0000030] fp ffffc000011c2e60 main() at ffffc0000083baa0 netbsd:main+0x2a0 [ 1.0000030] fp 0000000000000000 aarch64_start() at ffffc0000000187c netbsd:aarch64_start+0x107c [ 1.0000030] cpu0: End traceback... Stopped in pid 0.0 (system) at netbsd:cpu_Debugger+0x4: ret db{0}>