Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017, 2018, 2019, 2020 The NetBSD Foundation, Inc. All rights reserved. Copyright (c) 1982, 1986, 1989, 1991, 1993 The Regents of the University of California. All rights reserved. NetBSD 9.99.74 (RPIEB) #0: Wed Oct 28 07:34:01 JST 2020 rin@latipes:/usr/src/sys/arch/evbarm/compile/RPIEB total memory = 948 MB avail memory = 913 MB entropy: no seed from bootloader armfdt0 (root) simplebus0 at armfdt0: Raspberry Pi 2 Model B Rev 1.2 simplebus1 at simplebus0 simplebus2 at simplebus0 cpus0 at simplebus0 simplebus3 at simplebus0 cpu0 at cpus0: 600 MHz Cortex-A53 r0p4 (Cortex V8A core) cpu0: DC enabled IC enabled WB enabled EABT branch prediction enabled cpu0: 32KB/64B 2-way L1 VIPT Instruction cache cpu0: 32KB/64B 4-way write-back-locking-C L1 PIPT Data cache cpu0: 512KB/64B 16-way write-through L2 PIPT Unified cache vfp0 at cpu0: NEON MPE (VFP 3.0+), rounding, NaN propagation, denormals cpu1 at cpus0 cpu2 at cpus0 cpu3 at cpus0 simplebus4 at simplebus1 bcmicu0 at simplebus1 fclock0 at simplebus2: 19200000 Hz fixed clock (osc) bcmcprman0 at simplebus1: BCM283x Clock Controller bcmaux0 at simplebus1 fclock1 at simplebus2: 480000000 Hz fixed clock (otg) bcmicu1 at simplebus1: Multiprocessor gtmr0 at simplebus0: Generic Timer gtmr0: interrupting on local_intc irq 3 armgtmr0 at gtmr0: Generic Timer (19200 kHz, virtual) plcom0 at simplebus1: ARM PL011 UART plcom0: txfifo disabled plcom0: console plcom0: interrupting on icu irq 57 usbnopphy0 at simplebus0: USB PHY /soc/thermal@7e212000 at simplebus1 not configured /soc/dsi@7e209000 at simplebus1 not configured bcmgpio0 at simplebus1: GPIO controller 2835 bcmgpio0: pins 0..31 interrupting on icu irq 49 bcmgpio0: pins 32..54 interrupting on icu irq 50 gpio0 at bcmgpio0: 54 pins bcmdmac0 at simplebus1: DMA0 DMA2 DMA4 DMA5 DMA8 DMA9 DMA10 DMA11 /soc/power at simplebus1 not configured bsciic0 at simplebus1: Broadcom Serial Controller bsciic0: interrupting on icu irq 53 iic0 at bsciic0: I2C bus bcmpmwdog0 at simplebus1: Power management, Reset and Watchdog controller bcmmbox0 at simplebus1: VC mailbox bcmmbox0: interrupting on icu irq 65 vcmbox0 at bcmmbox0 /soc/timer@7e003000 at simplebus1 not configured /soc/txp@7e004000 at simplebus1 not configured bcmsdhost0 at simplebus1: SD HOST controller bcmsdhost0: interrupting on icu irq 56 bsciic1 at simplebus1: Broadcom Serial Controller bsciic1: interrupting on icu irq 53 iic1 at bsciic1: I2C bus /soc/pwm@7e20c000 at simplebus1 not configured bsciic2 at simplebus1: Broadcom Serial Controller bsciic2: interrupting on icu irq 53 iic2 at bsciic2: I2C bus /soc/vec@7e806000 at simplebus1 not configured dwctwo0 at simplebus1: USB controller dwctwo0: interrupting on icu irq 9 /soc/hdmi@7e902000 at simplebus1 not configured /soc/gpu at simplebus1 not configured genfb0 at simplebus1Vendor: [INN] Product: [3200] K3A8F HDMI Serial number: 01081620 Manufactured 2016 Week 32 EDID Version 1.3 EDID Comment: Video Input: 80 Digital Gamma: 2.20 Max Size: 70 cm x 39 cm Features: ea DPMS standby DPMS suspend DPMS active-off RGB Preferred timing Chroma Info: Red X: 0.679 Red Y: 0.679 Grn X: 0.206 Grn Y: 0.693 Blu X: 0.151 Blu Y: 0.054 Wht X: 0.313 Wht Y: 0.329 Range: Horizontal: 30 - 83 kHz Vertical: 49 - 72 Hz Max Dot Clock: 170 MHz Video modes: 720x400 @ 70Hz (28320 738 846 900 412 414 449 -H +V) 640x480 @ 60Hz (25175 656 752 800 490 492 525 -H -V) 800x600 @ 60Hz (40000 840 968 1056 601 605 628 +H +V) 1024x768 @ 60Hz (65000 1048 1184 1344 771 777 806 -H -V) 1280x1024 @ 60Hz (108000 1328 1440 1688 1025 1028 1066 +H +V) 1680x1050 @ 60Hz (147140 1784 1968 2256 1051 1054 1087 +H +V) 1920x1080 @ 60Hz (148500 2008 2052 2200 1084 1089 1125 +H +V) 1600x900 @ 60Hz (118996 1696 1864 2128 901 904 932 +H +V) 1440x900 @ 60Hz (106470 1520 1672 1904 901 904 932 +H +V) 1366x768 @ 60Hz (85750 1436 1579 1792 771 774 798 +H +V) Preferred mode: 1920x1080 @ 60Hz Number of extension blocks: 1 rpi_fb_init: addr = 0xfe402000 size = 8355840 rpi_fb_init: depth = 32 rpi_fb_init: pitch = 7680 rpi_fb_init: width = 1920 height = 1080 rpi_fb_init: vwidth = 1920 vheight = 1080 : switching to framebuffer console wsdisplay0 at genfb0 kbdmux 1: console (default, vt100 emulation) /soc/mailbox@7e00b840 at simplebus1 not configured armpmu0 at simplebus0: Performance Monitor Unit gpioleds0 at simplebus0: ACT PWR bcmrng0 at simplebus1: RNG entropy: ready cpu_hatch(cpu3): cpu_hatch(cpu1): vectors vbar=0x8008b620 vectorscpu_hatch(cpu2): vectors vbar=0x8008b620 stacks stacks vbar=0x8008b620 stacks tlb tlb tlbcpu1: 600 MHz Cortex-A53 r0p4 (Cortex V8A core) cpu1: DC enabled IC enabled WB enabled EABT branch prediction enabled cpu1: 32KB/64B 2-way L1 VIPT Instruction cache cpu1: 32KB/64B 4-way write-back-locking-C L1 PIPT Data cache cpu1: 512KB/64B 16-way write-through L2 PIPT Unified cache vfpvfp1 at cpu1: NEON MPE (VFP 3.0+), rounding, NaN propagation, denormals md(0x8007d1a8)cpu3 interrupts: 600 MHz Cortex-A53 r0p4 (Cortex V8A core) done! cpu3: DC enabled IC enabled WB enabled EABT branch prediction enabled cpu3: 32KB/64B 2-way L1 VIPT Instruction cache cpu3: 32KB/64B 4-way write-back-locking-C L1 PIPT Data cache cpu3: 512KB/64B 16-way write-through L2 PIPT Unified cache vfpvfp3 at cpu3: NEON MPE (VFP 3.0+), rounding, NaN propagation, denormals md(0x8007d1a8)cpu2 interrupts done! : 600 MHz Cortex-A53 r0p4 (Cortex V8A core) cpu2: DC enabled IC enabled WB enabled EABT branch prediction enabled cpu2: 32KB/64B 2-way L1 VIPT Instruction cache cpu2: 32KB/64B 4-way write-back-locking-C L1 PIPT Data cache cpu2: 512KB/64B 16-way write-through L2 PIPT Unified cache vfpvfp2 at cpu2: NEON MPE (VFP 3.0+), rounding, NaN propagation, denormals md(0x8007d1a8) interrupts done! sdmmc0 at bcmsdhost0 usb0 at dwctwo0: USB revision 2.0 armpmu0: interrupting on local_intc irq 9 uhub0 at usb0: NetBSD (0x0000) DWC2 root hub (0x0000), class 9/0, rev 2.00/1.00, addr 1 sdmmc0: direct I/O error 5, r=6 p=0xbb1e0f14 write sdmmc0: SD card status: 4-bit, C10, A1 ld0 at sdmmc0: <0x03:0x5344:SC16G:0x80:0x3d6326c0:0x123> ld0: 15193 MB, 7717 cyl, 64 head, 63 sec, 512 bytes/sect x 31116288 sectors ld0: 4-bit width, High-Speed/SDR25, 50.000 MHz uhub1 at uhub0 port 1: vendor 0424 (0x0424) product 9514 (0x9514), class 9/0, rev 2.00/2.00, addr 2 uhub1: multiple transaction translators usmsc0 at uhub1 port 1 usmsc0: vendor 0424 (0x0424) product ec00 (0xec00), rev 2.00/2.00, addr 3 smscphy0 at usmsc0 phy 1: SMSC LAN8700 10/100 Ethernet Transceiver, rev. 3 smscphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto usmsc0: Ethernet address b8:27:eb:cf:71:9a uhub2 at uhub1 port 2: VIA Labs, Inc. (0x2109) USB2.0 Hub (0x2813), class 9/0, rev 2.10/90.11, addr 4 uhub2: single transaction translator uhub3 at uhub2 port 2: VIA Labs, Inc. (0x2109) USB2.0 Hub (0x2813), class 9/0, rev 2.10/90.11, addr 5 uhub3: single transaction translator uhub4 at uhub3 port 3: Apple Inc. (0x05ac) Keyboard Hub (0x1005), class 9/0, rev 2.00/96.15, addr 6 uhub4: single transaction translator uhidev0 at uhub4 port 2 configuration 1 interface 0 uhidev0: Apple Inc. (0x05ac) Apple Keyboard (0x021d), rev 2.00/0.70, addr 7, iclass 3/1 ukbd0 at uhidev0: 8 Variable keys, 5 Array codes, apple fn key wskbd0 at ukbd0: console keyboard, using wsdisplay0 uhidev1 at uhub4 port 2 configuration 1 interface 1 uhidev1: Apple Inc. (0x05ac) Apple Keyboard (0x021d), rev 2.00/0.70, addr 7, iclass 3/0 uhid0 at uhidev1: input=1, output=0, feature=0 uhidev2 at uhub2 port 4 configuration 1 interface 0 uhidev2: vendor 192f (0x192f) USB Optical Mouse (0x0916), rev 2.00/2.00, addr 8, iclass 3/1 ums0 at uhidev2: 3 buttons and Z dir wsmouse0 at ums0 mux 0 umass0 at uhub1 port 3 configuration 1 interface 0 umass0: ASMT (0x174c) ASM105x (0x55aa), rev 2.10/1.00, addr 9 scsibus0 at umass0: 2 targets, 1 lun per target uhub0: illegal enable change, port 1 sd0 at scsibus0 target 0 lun 0: disk fixed sd0: 111 GB, 16383 cyl, 16 head, 63 sec, 512 bytes/sect x 234455040 sectors WARNING: 1 error while detecting hardware; check system log. boot device: sd0 root on sd0e dumps on sd0b root file system type: ffs kern.module.path=/stand/evbarm/9.99.74/modules WARNING: no TOD clock present WARNING: using filesystem time WARNING: CHECK AND RESET THE DATE!