[0000.141] [TegraBoot] (version 24.00.2015.42-mobile-ec3b827e) [0000.146] Processing in cold boot mode Bootloader 2 [0000.151] A02 Bootrom Patch rev = 63 [0000.154] Power-up reason: on button [0000.157] No Battery Present [0000.160] RamCode = 0 [0000.162] Platform has Ddr4 type ram [0000.166] max77620 disabling SD1 Remote Sense [0000.170] Setting Ddr voltage to 1125mv [0000.174] Serial Number of Pmic Max77663: 0x814b1 [0000.182] Entering ramdump check [0000.185] Get RamDumpCarveOut = 0x0 [0000.188] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.193] Last reboot was clean, booting normally! [0000.197] Sdram initialization is successful [0000.202] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.207] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.212] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.217] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.222] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.228] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.233] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.238] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.253] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.259] Platform-DebugCarveout: 0 [0000.262] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.267] Non secure mode. Disable rollback prevention [0000.272] AOTAG Init Done [0000.310] Using GPT Primary to query partitions [0000.315] Loading Tboot-CPU binary [0000.364] Verifying bootloader in OdmNonSecureSBK mode [0000.374] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.381] Bootloader downloaded successfully. [0000.385] Downloaded Tboot-CPU binary to 0xa0000258 [0000.390] MAX77620_GPIO1 Configured. [0000.394] MAX77620_GPIO5 Configured. [0000.397] CPU power rail is up [0000.400] CPU clock enabled [0000.404] Performing RAM repair [0000.407] Updating A64 Warmreset Address to 0xa00002e9 [0000.424] Bootloader DTB Load Address: 0x83000000 [0000.440] Kernel DTB Load Address: 0x83080000 [0000.445] Loading cboot binary [0000.539] Verifying bootloader in OdmNonSecureSBK mode [0000.643] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0000.650] Bootloader downloaded successfully. [0000.654] GPT: Partition NOT found ! [0000.657] Find Partition via GPT Failed [0000.661] Find Partition via PT Failed [0000.664] function NvTbootGetBinaryOffsets: 0x1 error [0000.669] Error in NvTbootLoadBinary: 0x1 ! [0000.673] Next binary entry address: 0x80110000 [0000.678] BoardId: 2180 [0000.704] NvTbootI2cProbe(): error code 0x00045100 Error while read [0000.710] Display board id is not available [0000.714] dram memory type is 3 [0000.718] WB0 init successful [0000.744] Bpmp FW successfully loaded [0000.748] Set NvDecSticky Bits [0000.751] GSC1 address : ff700000 [0000.754] GSC2 address ff63fffc value c0edbbcc [0000.759] GSC2 address : ff600000 [0000.763] GSC3 address : ff500000 [0000.767] GSC4 address : ff400000 [0000.770] GSC5 address : ff300000 [0000.773] GSC MC Settings done [0000.777] TOS old plaintext Image length 65536 [0000.783] *** Secure OS image signature not verified *** [0000.788] Loading and Validation of Secure OS Successful [0000.794] NvTbootPackSdramParams: start. [0000.799] NvTbootPackSdramParams: done. [0000.802] Tegraboot started after 119682 us [0000.806] Basic modules init took 302410 us [0000.810] Sec Bootdevice Read Time = 194 ms, Read Size = 8464 KB [0000.816] Sec Bootdevice Write Time = -1940251267 ms, Write Size = 343597383 KB [0000.823] Next stage binary read took 12257 us [0000.828] Carveout took 262424 us [0000.831] CPU initialization took 125281 us [0000.835] Total time taken by TegraBoot 702372 us [0000.839] Starting CPU & Halting co-processor 64b[0000.947] RamCode = 0 [0000.962] LPDDR4 Training: Read DT: Number of tables = 10 [0000.967] EMC Training (SRC-freq: 204000; DST-freq: 40800) [0000.972] EMC Training Skipped [0000.975] EMC Training (SRC-freq: 204000; DST-freq: 68000) [0000.980] EMC Training Skipped [0000.983] EMC Training (SRC-freq: 204000; DST-freq: 102000) [0000.988] EMC Training Skipped [0000.991] EMC Training (SRC-freq: 204000; DST-freq: 204000) [0000.996] EMC Training Skipped [0000.999] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0001.005] EMC Training Successful [0001.008] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0001.014] EMC Training Successful [0001.017] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0001.028] EMC Training Successful [0001.032] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0001.054] EMC Training Successful [0001.057] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.079] EMC Training Successful [0001.082] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.101] EMC Training Successful [0001.105] Switching to 800000 KHz Success [0001.111] DT Write: emc-table40800 succeeded [0001.117] DT Write: emc-table68000 succeeded [0001.124] DT Write: emc-table102000 succeeded [0001.130] DT Write: emc-table204000 succeeded [0001.136] DT Write: emc-table408000 succeeded [0001.143] DT Write: emc-table665600 succeeded [0001.149] DT Write: emc-table800000 succeeded [0001.155] DT Write: emc-table1065600 succeeded [0001.162] DT Write: emc-table1331200 succeeded [0001.168] DT Write: emc-table1600000 succeeded [0001.172] LPDDR4 Training: Write DT: Number of tables = 10 U-Boot 2017.07 (Sep 23 2017 - 14:28:01 -0300) TEGRA210 Model: NVIDIA P2371-2180 Board: NVIDIA P2371-2180 DRAM: 3.5 GiB MMC: sdhci700b0000: 1, sdhci@700b0600: 0 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2 1 0 switch to partitions #0, OK mmc1 is current device Scanning mmc 1:1... Found /extlinux/extlinux.conf Retrieving file: /extlinux/extlinux.conf reading /extlinux/extlinux.conf 186 bytes read in 12 ms (14.6 KiB/s) NetBSD/arm64 boot options 1: NetBSD/arm64 Enter choice: 1: NetBSD/arm64 Retrieving file: /netbsd.ub reading /netbsd.ub 8215592 bytes read in 379 ms (20.7 MiB/s) append: root=ld0a console=fb Retrieving file: /dtb/tegra210-p2371-2180.dtb reading /dtb/tegra210-p2371-2180.dtb 54550 bytes read in 23 ms (2.3 MiB/s) ## Flattened Device Tree blob at 82000000 Booting using the fdt blob at 0x82000000 Using Device Tree in place at 0000000082000000, end 0000000082010515 Starting kernel ... ksyms: checking .text ksyms: checking .rodata ksyms: checking link_set_evcnts ksyms: checking link_set_arm_platforms ksyms: checking link_set_fdt_consoles ksyms: checking link_set_modules ksyms: checking link_set_sysctl_funcs ksyms: checking link_set_ieee80211_funcs ksyms: checking link_set_domains ksyms: checking link_set_sdt_probes_set ksyms: checking link_set_sdt_argtypes_set ksyms: checking link_set_sdt_providers_set ksyms: checking link_set_dkwedge_methods ksyms: checking link_set_prop_linkpools ksyms: checking .eh_frame ksyms: checking .got ksyms: checking .got.plt ksyms: checking .data ksyms: checking .data.cacheline_aligned ksyms: checking .data.read_mostly ksyms: checking .ident ksyms: checking .comment ksyms: checking .note.netbsd.ident ksyms: checking .shstrtab ksyms: checking .symtab ksyms: checking .strtab Loaded initial symtab at 0xffffffc0006950f8, strtab at 0xffffffc0007334b0, # entries 27005 Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017, 2018 The NetBSD Foundation, Inc. All rights reserved. Copyright (c) 1982, 1986, 1989, 1991, 1993 The Regents of the University of California. All rights reserved. NetBSD 8.99.12 (GENERIC64) #81: Sun Feb 4 16:31:17 AST 2018 jmcneillpersona.local:/Users/jmcneill/netbsd/rpi64wip/sys/arch/evbarm/compile/obj/GENERIC64 total memory = 3576 MB avail memory = 3454 MB armfdt0 (root) fdt0 at armfdt0: NVIDIA Jetson TX1 Developer Kit fdt1 at fdt0 fdt2 at fdt0 fdt3 at fdt0 fdt4 at fdt0 cpus0 at fdt0 cpu0 at cpus0: Cortex-A57 r1p1 (Cortex V8-A core) cpu0: CPU Affinity 0-0-0-0 cpu0: IC enabled, DC enabled, EL0/EL1 stack Alignment check enabled cpu0: Cache Writeback Granule 16B, Exclusives Reservation Granule 16B cpu0: L1 48KB/64B 3-way read-allocate PIPT Instruction cache cpu0: L1 32KB/64B 2-way write-back read-allocate write-allocate PIPT Data cache cpu0: L2 2048KB/64B 16-way write-back read-allocate write-allocate PIPT Unified cache cpu0: revID=0x200, PMCv3, 4k table, 64k table, 16bit ASID cpu0: auxID=0x11120, FP, CRC32, SHA1, SHA256, AES+PMULL, NEON, rounding, NaN propagation, denormals, 32x64bitRegs, Fused Multiply-Add cpu1 at cpus0: disabled (uniprocessor kernel) cpu2 at cpus0: disabled (uniprocessor kernel) cpu3 at cpus0: disabled (uniprocessor kernel) tegralic0 at fdt0: LIC gic0 at fdt0: GIC armgic0 at gic0: Generic Interrupt Controller, 224 sources (213 valid) armgic0: 16 Priorities, 192 SPIs, 6 PPIs, 15 SGIs fclock0 at fdt3: 32768 Hz fixed clock gtmr0 at fdt0: Generic Timer gtmr0: interrupting on GIC irq 27 armgtmr0 at gtmr0: ARMv7 Generic 64-bit Timer (19200 kHz) tegragpio0 at fdt0: GPIO gpio0 at tegragpio0 (A): 8 pins gpio1 at tegragpio0 (B): 8 pins gpio2 at tegragpio0 (C): 8 pins gpio3 at tegragpio0 (D): 8 pins gpio4 at tegragpio0 (E): 8 pins gpio5 at tegragpio0 (F): 8 pins gpio6 at tegragpio0 (G): 8 pins gpio7 at tegragpio0 (H): 8 pins gpio8 at tegragpio0 (I): 8 pins gpio9 at tegragpio0 (J): 8 pins gpio10 at tegragpio0 (K): 8 pins gpio11 at tegragpio0 (L): 8 pins gpio12 at tegragpio0 (M): 8 pins gpio13 at tegragpio0 (N): 8 pins gpio14 at tegragpio0 (O): 8 pins gpio15 at tegragpio0 (P): 8 pins gpio16 at tegragpio0 (Q): 8 pins gpio17 at tegragpio0 (R): 8 pins gpio18 at tegragpio0 (S): 8 pins gpio19 at tegragpio0 (T): 8 pins gpio20 at tegragpio0 (U): 8 pins gpio21 at tegragpio0 (V): 8 pins gpio22 at tegragpio0 (W): 8 pins gpio23 at tegragpio0 (X): 8 pins gpio24 at tegragpio0 (Y): 8 pins gpio25 at tegragpio0 (Z): 8 pins gpio26 at tegragpio0 (AA): 8 pins gpio27 at tegragpio0 (BB): 8 pins gpio28 at tegragpio0 (CC): 8 pins gpio29 at tegragpio0 (DD): 8 pins gpio30 at tegragpio0 (EE): 8 pins tegra210car0 at fdt0: CAR tegrai2c0 at fdt0: I2C tegrai2c0: interrupting on irq 85 iic0 at tegrai2c0: I2C bus max77620pmic0 at iic0 addr 0x3c: MAX77620 Power Management IC tegrapmc0 at fdt0: PMC fregulator0 at fdt1: AVDD_DSI_CSI_1V2 fregulator1 at fdt1: VDD_5V0_IO_SYS tegrai2c1 at fdt0: I2C tegrai2c1: interrupting on irq 116 iic1 at tegrai2c1: I2C bus tcagpio0 at iic1 addr 0x74: I2C/SMBus I/O Expander backlight at iic1 addr 0x2c not configured fregulator2 at fdt1: VDD_HDMI_5V0 tegrai2c2 at fdt0: I2C tegrai2c2: interrupting on irq 152 iic2 at tegrai2c2: I2C bus tegraapbdma0 at fdt0: APBDMA fregulator3 at fdt1: VDD_5V0_SYS fregulator4 at fdt1: VDD_3V3_SYS fregulator5 at fdt1: RTL_5V fregulator6 at fdt1: USB_VBUS_EN1 fregulator7 at fdt1: VDD_3V3_SD fregulator8 at fdt1: VDD_SYS_MUX tegrafuse0 at fdt0: FUSE fregulator9 at fdt1: VDD_DIS_3V3_LCD fregulator10 at fdt1: VDD_LCD_1V8_DIS tegra210xpad0 at fdt0: XUSB PADCTL tegra210xphy0 at tegra210xpad0: usb2-0 tegra210xphy1 at tegra210xpad0: usb2-1 tegra210xphy2 at tegra210xpad0: usb2-2 tegra210xphy3 at tegra210xpad0: usb2-3 tegra210xphy4 at tegra210xpad0: pcie-0 tegra210xphy5 at tegra210xpad0: pcie-1 tegra210xphy6 at tegra210xpad0: pcie-2 tegra210xphy7 at tegra210xpad0: pcie-3 tegra210xphy8 at tegra210xpad0: pcie-4 tegra210xphy9 at tegra210xpad0: pcie-5 tegra210xphy10 at tegra210xpad0: pcie-6 tegra210xphy11 at tegra210xpad0: sata-0 tegra210xpad0: port usb2-0: set mode otg, external tegra210xpad0: port usb2-1: set mode host, external tegra210xpad0: port usb2-2: set mode host, external tegra210xpad0: port usb2-3: set mode host, external tegra210xpad0: port usb3-0: set companion usb2-1, external tegra210xpad0: port usb3-1: set companion usb2-2, external /memory-controller70019000 at fdt0 not configured /mipi700e3000 at fdt0 not configured /host1x50000000/dpaux@54040000 at fdt2 not configured /regulators/regulator100 at fdt1 not configured tegrapinmux0 at fdt0: Pinmux /pwm7000a000 at fdt0 not configured /thermal-sensor700e2000 at fdt0 not configured /pcie1003000 at fdt0 not configured /gpu57000000 at fdt0 not configured tegratimer0 at fdt0: Timers tegratimer0: default watchdog period is 10 seconds /flow-controller60007000 at fdt0 not configured /apbmisc70000800 at fdt0 not configured com0 at fdt0: Tegra UART, working fifo com0: console com0: interrupting on irq 68 tegrartc0 at fdt0: RTC tegrartc0: disabled xhci0 at fdt0: XUSB xhci0: interrupting on irq 71 xhci0: interrupting on irq 72 tegra210xpad0: lane usb2-0: set func xusb tegra210xpad0: lane usb2-1: set func xusb tegra210xpad0: lane usb2-2: set func xusb tegra210xpad0: lane usb2-3: set func xusb tegra210xpad0: lane pcie-6: set func usb3-ss tegra210xpad0: timeout calibrating UPHY PLL (1) tegra210xpad0: lane pcie-5: set func usb3-ss tegra210xpad0: timeout calibrating UPHY PLL (1) xhci0: couldn't acquire supply 'dvddio-pex-supply' xhci0: couldn't acquire supply 'hvddio-pex-supply' xhci0: couldn't acquire supply 'avdd-pll-utmip-supply' xhci0: couldn't acquire supply 'avdd-pll-uerefe-supply' xhci0: couldn't acquire supply 'dvdd-usb-ss-pll-supply' xhci0: couldn't acquire supply 'hvdd-usb-ss-pll-e-supply' sdhc0 at fdt0: SDMMC (81600 kHz) sdhc0: interrupting on irq 46 sdhc0: SDHC 4.0, rev 3, 32-bit ADMA2, 81600 kHz, HS 1.8V 3.0V 3.3V, re-tuning mode 1, 512 byte blocks sdmmc0 at sdhc0 slot 0 sdhc1 at fdt0: SDMMC (81600 kHz) sdhc1: interrupting on irq 63 sdhc1: SDHC 4.0, rev 3, 32-bit ADMA2, 81600 kHz, HS 1.8V 3.0V 3.3V, re-tuning mode 1, 512 byte blocks sdmmc1 at sdhc1 slot 0 gpiokeys0 at fdt0: Power, Volume Down, Volume Up wskbd0 at gpiokeys0 mux 1 /host1x50000000/tsec@54100000 at fdt2 not configured /host1x50000000/dc@54200000 at fdt2 not configured /host1x50000000/dc@54240000 at fdt2 not configured /host1x50000000/dsi@54300000 at fdt2 not configured /host1x50000000/vic@54340000 at fdt2 not configured /host1x50000000/sor@54580000 at fdt2 not configured sdhc0: cmd timeout error sdhc1: cmd timeout error ld1 at sdmmc1: <0x11:0x0100:016G32:0x00:0xf271c147:0x000> ld1: 15028 MB, 7633 cyl, 64 head, 63 sec, 512 bytes/sect x 30777344 sectors sdmmc0: SD card status: 4-bit, C10, U1, V10 ld0 at sdmmc0: <0x27:0x5048:2&DRP:0x07:0x01c8c6c9:0x109> ld0: 15288 MB, 7765 cyl, 64 head, 63 sec, 512 bytes/sect x 31309824 sectors dk0 at ld1: "APP", 29360128 blocks at 34, type: dk1 at ld1: "TBC", 4096 blocks at 29360162, type: dk2 at ld1: "EBT", 8192 blocks at 29364258, type: dk3 at ld1: "BPF", 4096 blocks at 29372450, type: dk4 at ld1: "WB0", 12288 blocks at 29376546, type: dk5 at ld1: "RP1", 8192 blocks at 29388834, type: dk6 at ld1: "TOS", 12288 blocks at 29397026, type: dk7 at ld1: "EKS", 4096 blocks at 29409314, type: dk8 at ld1: "FX", 4096 blocks at 29413410, type: dk9 at ld1: "SOS", 40960 blocks at 29417506, type: dk10 at ld1: "EXI", 131072 blocks at 29458466, type: dk11 at ld1: "LNX", 131072 blocks at 29589538, type: dk12 at ld1: "DTB", 8192 blocks at 29720610, type: dk13 at ld1: "NXT", 4096 blocks at 29728802, type: dk14 at ld1: "MXB", 12288 blocks at 29732898, type: dk15 at ld1: "MXP", 12288 blocks at 29745186, type: dk16 at ld1: "USP", 4096 blocks at 29757474, type: dk17 at ld1: "UDA", 1015741 blocks at 29761570, type: ld1: 8-bit width, 4096 KB cache, 52.000 MHz ld0: 4-bit width, High-Speed/SDR25, 50.000 MHz WARNING: 8 errors while detecting hardware; check system log. boot device: ld0 root on ld0a dumps on ld0b mountroot: trying ext2fs... mountroot: trying ffs... root file system type: ffs kern.module.path=/stand/evbarm/8.99.12/modules WARNING: no TOD clock present WARNING: using filesystem time WARNING: CHECK AND RESET THE DATE! usb0 at xhci0: USB revision 3.0 uhub0 at usb0: vendor 0000 (0000) xHCI Root Hub (0000), class 9/0, rev 3.00/1.00, addr 0 usb1 at xhci0: USB revision 2.0 uhub1 at usb1: vendor 0000 (0000) xHCI Root Hub (0000), class 9/0, rev 2.00/1.00, addr 0 init: copying out path `/sbin/init' 11 Sun Feb 4 20:25:49 UTC 2018 Starting root file system check: cdce0 at uhub1 port 2 configuration 2 interface 0 cdce0: Nvidia (0x955) USB 10/100/1000 LAN (0x9ff), rev 2.10/30.00, addr 1 cdce0: address 00:04:4b:79:45:4e /dev/rld0a: INCORRECT BLOCK COUNT I=13074 (16 should be 0) (CORRECTED) /dev/rld0a: UNREF FILE I=13074 OWNER=0 MODE=100644 /dev/rld0a: SIZE=0 MTIME=Feb 4 20:25 2018 (CLEARED) /dev/rld0a: FREE BLK COUNT(S) WRONG IN SUPERBLK (SALVAGED) /dev/rld0a: SUMMARY INFORMATION BAD (SALVAGED) /dev/rld0a: BLK(S) MISSING IN BIT MAPS (SALVAGED) /dev/rld0a: 26316 files, 169691 used, 1727868 free (36 frags, 215979 blocks, 0.0% fragmentation) /dev/rld0a: MARKING FILE SYSTEM CLEAN Not resizing /: already correct size swapctl: adding /dev/ld0b as swap device at priority 0 Starting file system checks: /dev/rld0e: 153 files, 83988 free (20997 clusters) Loaded entropy from /var/db/entropy-file. Setting tty flags. Setting sysctl variables: ddb.onpanic: 1 -> 0 Starting network. Hostname: arm64 IPv6 mode: host Configuring network interfaces:. Adding interface aliases:. Waiting for DAD to complete for statically configured addresses... Starting dhcpcd. Building databases: dev, utmp, utmpx. Starting syslogd. Mounting all file systems... Clearing temporary files. Checking quotas: done. Setting securelevel: kern.securelevel: 0 -> 1 Starting virecover. Starting devpubd. Starting local daemons:. Updating motd. Starting ntpd. Starting sshd. Starting inetd. Starting cron. Sun Feb 4 20:26:25 UTC 2018 NetBSD/evbarm (arm64) (console) login: